Bmw Motor Swap

[Farbin Kaiber]

...you'll be bat shit insane fast

Is there a write-up on this ability? I searched for the "Offical r3vlimited.com Bat Shit Insane Fast Mods List", but it was not to be found. Can you describe this in detail?

[atomic]

Farbin Kaiber and psloan

check out below for bat shit insane fast motor swap info

http://www.r3vlimited.com/board/showthread.php?t=100260

[Farbin Kaiber]

Very informative. Covers the basics as well.

[Turf1600]

Bat shit insane fast mod list - for a 325i.

BMW 1600 m10 conversion
2002 turbo pistons - 6.9:1 compression
3 headgaskets for extra seal
suck 25 lbs of sand through the intake to port and polish - just be sure to change the oil afterwards.
2.9 open diff
84 318i suspension and BBK conversion
solex 1 barrel carb - drill out the jets for nawws
all tokiko shocks and springs
HUGE chrome tach
Fender vents
lamin x all lights BLACK
non painted eyebrows

[Farbin Kaiber]

Bat shit insane fast mod list - for a 325i.

BMW 1600 m10 conversion
2002 turbo pistons - 6.9:1 compression
3 headgaskets for extra seal
suck 25 lbs of sand through the intake to port and polish - just be sure to change the oil afterwards.
2.9 open diff
84 318i suspension and BBK conversion
solex 1 barrel carb - drill out the jets for nawws
all tokiko shocks and springs
HUGE chrome tach
Fender vents
lamin x all lights BLACK
non painted eyebrows

Is that the two 12.5 lbs. bags, or the one 25 lbs. bag? I wondered since the last time I read about this setup. Thanks In Advance.

TTFN-:)


P.s. You GuYz r teh Bst.

kthnxbye

[Turf1600]

Is that the two 12.5 lbs. bags, or the one 25 lbs. bag? I wondered since the last time I read about this setup. Thanks In Advance.

TTFN-:)


P.s. You GuYz r teh Bst.

kthnxbye

suck one 12.5 bag into the intake.

with the 2nd 12.5 bag - here's the procedure.

Open your valve cover.

Turn a shop vac onto "reverse"

Feed the sand into the hose on the shop vac and spray it all inside your valve cover.

Proceed to "wash the sand down" with oil

run the car at 6k RPMS for 30 minutes to polish your main and rod bearings.

After this step is completed - change your oil and run 10's.

[Farbin Kaiber]

sweet.





So, anyone want this obd1 converted, e34 oil panned, m50 manifolded s52 w/ e36 engine mount arms, e34 m5 engine mounts, e21 brake boostered, getrag 260 pile of parts, Im going with the "Offical r3vlimited.com Bat Shit Insane Fast Mods List". Screw what I had planned.

[Turf1600]

sweet.





So, anyone want this obd1 converted, e34 oil panned, m50 manifolded s52 w/ e36 engine mount arms, e34 m5 engine mounts, e21 brake boostered, getrag 260 pile of parts, Im going with the "Offical r3vlimited.com Bat Shit Insane Fast Mods List". Screw what I had planned.

It's probably only worth it's weight in scrap.

[atomic]

sweet.





So, anyone want this obd1 converted, e34 oil panned, m50 manifolded s52 w/ e36 engine mount arms, e34 m5 engine mounts, e21 brake boostered, getrag 260 pile of parts, Im going with the "Offical r3vlimited.com Bat Shit Insane Fast Mods List". Screw what I had planned.

Can you ship to nigeria ?

[Farbin Kaiber]

Scrap in Nigeria go for a higher value?

[atomic]

Farbin - If you will go ahead and ship out those motor swap parts via UPS freight to address in nigeria provided, and once it is sent provide paypal with the tracking number and then the funds will be released to your account. Its a win - win deal for both of us ....

[whiltebeitel]

Damn, this is harsh, but deserved.

ROFLMAO

[mudflaps]

im confused on the sand mod?


I always used cat litter, it always did the ports better justice.

[Turf1600]

im confused on the sand mod?


I always used cat litter, it always did the ports better justice.

Clay or clumping?

[Farbin Kaiber]

Ok, so what do I torque these head bolts down too?