JackBenny's 1991 318is Project

[jackbenny]

Here's a pic of mine:



Fits with intake manifold and m3 harness covers just fine:

Yep, I've referenced those pictures previously as to what I'm doing wrong. Maybe because the motor is shimmed? I dunno. I'm routing the fuel injection harness below and that helps clean it up. The bellow was hitting the manifold pretty hard though so eliminating it looks a bit better and makes everything clear. I hope I can get the relays back under the cover though. The manifold hit the plastic underneath the relays. Perhaps if I remove that piece there would be enough clearance? Tired of slapping the manifold back on and off though. Ideally I would get my hoses set, slap the manifold on and then finish routing the wires.

Yours is quite clean though...

[lifeiskaos]

Yep, I've referenced those pictures previously as to what I'm doing wrong. Maybe because the motor is shimmed? I dunno. I'm routing the fuel injection harness below and that helps clean it up. The bellow was hitting the manifold pretty hard though so eliminating it looks a bit better and makes everything clear. I hope I can get the relays back under the cover though. The manifold hit the plastic underneath the relays. Perhaps if I remove that piece there would be enough clearance? Tired of slapping the manifold back on and off though. Ideally I would get my hoses set, slap the manifold on and then finish routing the wires.

Yours is quite clean though...

Yeah, you don't use the plastic part under the relays. Also, you can see that I had to trim the main cover to clear the manifold.

Love your project BTW!

[Gnarles]

I used the e36 upper and lower radiator hoses and they fit perfectly with my m20 radiator. Also, I reused my m20 hoses to and from the firewall with the bypass system still intact. I think I had to trim the one that connects to the obd2 coolant pipe slightly. I had to bend the top heater core pipe down and towards the engine otherwise the top heater hose would interfere with the fpr vacuum line attachment to the intake manifold.

[jackbenny]

Yeah, you don't use the plastic part under the relays. Also, you can see that I had to trim the main cover to clear the manifold.

Love your project BTW!

That makes sense. It still looked pretty close. No issues with the engine torquing over?

I used the e36 upper and lower radiator hoses and they fit perfectly with my m20 radiator. Also, I reused my m20 hoses to and from the firewall with the bypass system still intact. I think I had to trim the one that connects to the obd2 coolant pipe slightly. I had to bend the top heater core pipe down and towards the engine otherwise the top heater hose would interfere with the fpr vacuum line attachment to the intake manifold.

I took apart my M42 hoses last night to see if any fit. I didn't get very far but the ones I did try looked too convoluted and not very "pretty". I have a couple of hoses that might work for the ICV. More importantly I found a reducer for the ICV to throttle body boot.

Got two packages yesterday. Starts with R and ends in O. Been waiting for these for a while. I'll take some pictures when I get back this weekend.

[flipper325es]

Got two packages yesterday. Starts with R and ends in O. Been waiting for these for a while. I'll take some pictures when I get back this weekend.

What will you use to mount them? One of these?

http://www.r3vlimited.com/board/showthread.php?t=142520

http://www.r3vlimited.com/board/showthread.php?t=168663

http://www.r3vlimited.com/board/showthread.php?t=162487&highlight=sidemounts

[jackbenny]

What will you use to mount them? One of these?

http://www.r3vlimited.com/board/showthread.php?t=142520

http://www.r3vlimited.com/board/showthread.php?t=168663

http://www.r3vlimited.com/board/show...ght=sidemounts

I sold my original seats with sliders to a buddy so he could use them for his '48 F1 project. So I believe I have recaro sliders with an E30 specific base. I say believe because I got those mounts over a month ago and I just can't remember. Had I gone fixed back I would have probably gone with Massive mounting brackets. It was all a package deal.

They are Recaro Speeds that are black with red stitching and the 5th hole for a harness if and when I decide to go that route. They are quite comfortable and should look pretty nice with the rest of the interior plans.

I'll try and get a cell phone picture uploaded.

[Mtriple]

Your car was a large source of inspiration for my interior Mr. Cooper. :D

BTW, what did you use for carpet? Just perlon felt or ozite?

Thank you sir! I used accoustic carpet (unbacked) that you can find at any good car audio shop. It's light and very stretchable...

[brokEe30]

Know that you are getting close to being a dad. I am excited for you and your wife. Gotta get an update on this please.

[phenryiv1]

Thank you sir! I used accoustic carpet (unbacked) that you can find at any good car audio shop. It's light and very stretchable...

I could not find a thread with your carpet install. Link? (Sorry for the slight threadjack.)

[jackbenny]

I could not find a thread with your carpet install. Link? (Sorry for the slight threadjack.)

There are some decent pictures here.

http://www.e30tech.com/featured/mtriple/

But it's the finished product of course. ;)

[jackbenny]

Know that you are getting close to being a dad. I am excited for you and your wife. Gotta get an update on this please.

Yeah, I know, I've been slacking. I have some pictures taken but not much has happened since the last update. On the plus side I just emptied my bank account with another blunttech order. I'm hoping I can provide some good updates this weekend as well.

[brokEe30]

Yeah, I know, I've been slacking. I have some pictures taken but not much has happened since the last update. On the plus side I just emptied my bank account with another blunttech order. I'm hoping I can provide some good updates this weekend as well.

Awesome brother. Keep forging ahead.

[jackbenny]

Just one obnoxiously sized cell phone picture before I go to bed



Damn that is blurry. It almost qualifies as a teaser. I'll try take a better pic and get more pictures uploaded tomorrow.

G' night.

[Jean]

Very nice progress dude!

[Dj Buttchug]

nice build man. Props!