homebuying fun (caution: stupidly wide .jpg)

[mrsleeve]

Carriage bolts are nice because of the square section that you tap in place, which holds the bolt and normally stops it from turning when you fasten it. The other bonus is that the bolts don't snag on things the way allthread or exposed nuts might. Granted allthread is cheaper, and you can always countersink it so it's not proud of the surface.

That's a nice worktop in the vid, but it's overkill, and you should always have a sacrificial top unless you really like splinters/an ugly bench. Metal tops are also nice, but can be expensiveish.

I dont disagree with a sacrificial top for a lot of what car guys do if your bench is wood. I have a 8x3 all steel shop bench that I have for all that kinda thing (though I need to put a couple stringers under it to stiffen it up at somepoint) The all-thread leaves room to cinch things up down then line if need be, and with a carriage bolt you have to counter sink the threaded end with the nut anyway, so why not just take an extra 5 min and counter sink both face plates and do it that way to gain serviceability in the future.

I really need to work on getting my shop in a work able state but its 2 weeks worth of work just to get it organized to the point of starting to organize it

[Motheye99]

Look into adding some caster wheels from harbor freight, locking ones. It would make it a lot easier to move engine blocks in and out of your garage. I don't know about your garage but I don't have a tall enough ceiling too hoist motors up high enough to hoist motors. Just a Idea

You can do a lot with a jig saw, no need for much more IMO.

[roguetoaster]

Carriage bolts are nice because of the square section that you tap in place, which holds the bolt and normally stops it from turning when you fasten it. The other bonus is that the bolts don't snag on things the way allthread or exposed nuts might. Granted allthread is cheaper, and you can always countersink it so it's not proud of the surface.

That's a nice worktop in the vid, but it's overkill, and you should always have a sacrificial top unless you really like splinters/an ugly bench. Metal tops are also nice, but can be expensiveish.

[mrsleeve]

Reposting this pics, but for a different reason... I need your help/ advice



I want to build a work bench area in the back of the garage, to the right of the tool box (when you're looking at the pic).

I have a hammer, and a tape measure but pretty much nothing else really in the woodworking dept. Need a suggestion of basic tools and ideas on materials needed. Basically looking for a table that can hold an engine block (m20 ;) ) strong enough to anchor a vice, a shelf underneath for stashing stuff. Nothing too crazy especially since my wife will be backing her SUV nearly into the bench, so maybe some safeguards also to prevent her from destroying it haha

thanks

Youtube is good for this, and if you dont live under a rock on YT you have seen at least one of this guys vids pop up, Cody aka Wrangerlstar is building exctally want you want right now. I would do like him and use all thread and not carriage bolts but thats me.... I am still trying to get my all inlaws shit out of my shop and move into to it for the last 2 years and I am going to build a bench like this for general use outside of welding and very oily things once I have the room to do so

https://www.youtube.com/watch?v=BFRqM6LquIE

[2mAn]

Awesome! Thank you. I have a drill and Im not afraid to use it. Its the saw's that I dont have.

I will update this when I finish it off.

[roguetoaster]

Build the entire structure of the bench out of 2x4s, put a sacrificial plywood top on it. Fasten it all together with carriage bolts.

Tools beyond what you have:

Circular saw - $20 used
Coarse and fine blade for saw - $15
Drill - $20 used
Drill bit for carriage bolt shank size - $3
Countersink or step drill bit to recess the head of the carriage bolts - $5

^
Ideally you should borrow those tools and their owner if you have zero experience.

1 sheet 3/4" ply - $25
12-16 2x4s - $30-40
Hardware - $30

The best safeguard to prevent collision is a block fixed to the floor that will effectively stop the vehicle via tire contact.

[2mAn]

Reposting this pics, but for a different reason... I need your help/ advice



I want to build a work bench area in the back of the garage, to the right of the tool box (when you're looking at the pic).

I have a hammer, and a tape measure but pretty much nothing else really in the woodworking dept. Need a suggestion of basic tools and ideas on materials needed. Basically looking for a table that can hold an engine block (m20 ;) ) strong enough to anchor a vice, a shelf underneath for stashing stuff. Nothing too crazy especially since my wife will be backing her SUV nearly into the bench, so maybe some safeguards also to prevent her from destroying it haha

thanks

[mrsleeve]

Thanks guys.

While I was doing shit. I spent the better part of an after noon. In my crawl space cleaning up the satellite TV installation and relocating some of thier work. Running cat5e and installing wall boxes in for coaix and cat5e in the living room, office, master and spare bedroom, with a network box in the office for all that. Built a new TV stand for the living room out flooring cut offs and scrap.

Next up.is painting all the doors and trim to get rid of this god awful orange untill it can be replaced, and maybe a old office desk restoration to undertake before going back to work.

[Kershaw]

That looks awesome.

[mbonder]

Looks good, in the end you'll be happier having the hardwood. New trims and doors will definitely make a difference as well.

[mrsleeve]

How much that set you back?

Wood was 6.50 a foot... sand and finish was 3 a foot so I have about 11k in in just a few feet shy of a 1000 sq/ft. With incidentals and what not

[george graves]

At least 2k a room.

[bmwm42]

and TIME!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!


The sanding guy got the last coat of finish on this am..... Cant wait to move back into my house tomorrow am. Wide plank rustic Quarter and Rift sawn white oak, no stain just natural, sealed up with Bona mega water base.

2019-02-03_03-07-18 by mrsleeve, on Flickr


Next time I get some cash saved up, all new trim and Doors in the whole house (ALDER all the way though) , that cheap ass fir turns red and with a light brown stain on it. its FUCKING ORANGE.... I always thought it was orange but not this orange lol

How much that set you back?

[LJ851]

That looks fantastic, Sleeve !

[mrsleeve]

and TIME!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!


The sanding guy got the last coat of finish on this am..... Cant wait to move back into my house tomorrow am. Wide plank rustic Quarter and Rift sawn white oak, no stain just natural, sealed up with Bona mega water base.

2019-02-03_03-07-18 by mrsleeve, on Flickr


Next time I get some cash saved up, all new trim and Doors in the whole house (ALDER all the way though) , that cheap ass fir turns red and with a light brown stain on it. its FUCKING ORANGE.... I always thought it was orange but not this orange lol