M42 rad + M50 overheating woes.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • lolcantturn
    R3V Elite
    • Oct 2010
    • 4588

    #1

    M42 rad + M50 overheating woes.

    Got an M42 rad. Got an 80*C t-stat. Got a 14" IE Fan wired in properly. Brand new coolant temp sender (to the gauge)

    When I'm on the highway, my temp gauge just climbsssss. The faster I go, the more the revs build up, the hotter it gets even with the heat on. The heat is basically fire.
    When I'm idling, it'll stay right below the halfway mark.

    what the heck is the deal? I left the rad cap off and the bleed screw off and let it idle for about 10mins with no problems and the heat on to let itself bleed through and it didn't overheat, but when i put the cap on and bleed screw on and drive normally it'll just heat up.

    Thoughts?
    Originally posted by TSI
    ♫ Rust flecks are falling on my head...♫
    OEM+
  • KenC
    King of Kegstands
    • Oct 2003
    • 14396

    #2
    Coolant lines into the heater core might be backwards.
    Originally posted by Gruelius
    and i do not know what bugg brakes are.

    Comment

    • lolcantturn
      R3V Elite
      • Oct 2010
      • 4588

      #3
      but my heat is super hawt, wouldn't it just not work ?
      Originally posted by TSI
      ♫ Rust flecks are falling on my head...♫
      OEM+

      Comment

      • KenC
        King of Kegstands
        • Oct 2003
        • 14396

        #4
        Do the heat output temps fluctuate at all? Hotter at idle than driving?
        Originally posted by Gruelius
        and i do not know what bugg brakes are.

        Comment

        • lolcantturn
          R3V Elite
          • Oct 2010
          • 4588

          #5
          Seems roughly the same. A little hotter driving but i guess that's cause my car's overheating haha.
          Originally posted by TSI
          ♫ Rust flecks are falling on my head...♫
          OEM+

          Comment

          • KenC
            King of Kegstands
            • Oct 2003
            • 14396

            #6
            It doesn't make sense that it cools down at idle. Is your t-stat stuck closed... or open?
            Originally posted by Gruelius
            and i do not know what bugg brakes are.

            Comment

            • lolcantturn
              R3V Elite
              • Oct 2010
              • 4588

              #7
              I have no idea. It's fairly old but came from a known working well never-overheated M20.
              Originally posted by TSI
              ♫ Rust flecks are falling on my head...♫
              OEM+

              Comment

              • sticksdaman
                R3VLimited
                • Apr 2005
                • 2987

                #8
                Perhaps your drive belt is slipping? If your belt isnt under enough tension it may not be turning your water pump fast enough to keep up with the engine at higher revs. That may explain why at idle it's fine but at speed it isnt pumping enough coolant in/out fast enough to maintain an optimal temp.
                Originally posted by ebelements
                Also, for those who don't know, negative camber is the greatest thing since sliced bread(panera). Even tire wear is for city busses and the elderly.

                Comment

                • lolcantturn
                  R3V Elite
                  • Oct 2010
                  • 4588

                  #9
                  My drive belt is pretty darn tight. ill double check.
                  Originally posted by TSI
                  ♫ Rust flecks are falling on my head...♫
                  OEM+

                  Comment

                  • trackjunkie21
                    No R3VLimiter
                    • Jan 2010
                    • 3962

                    #10
                    uhm why reuse a thermostat? It's a couple bucks and it's not worth the risk to use an old one.
                    Your signature picture has been removed since it contained the Photobucket "upgrade your account" image.

                    Originally posted by Wh33lhop
                    VANOS: sometimes you just need to go full retard.

                    Comment

                    • AndrewBird
                      The Mad Scientist
                      • Oct 2003
                      • 11892

                      #11
                      Your cooling fan isn't accidentally set to blow AWAY from the engine (forward), is it? Had a friend do this with a mechanical fan. Took him forever to figure out why the car was over heating.

                      Comment

                      • lolcantturn
                        R3V Elite
                        • Oct 2010
                        • 4588

                        #12
                        Originally posted by trackjunkie21
                        uhm why reuse a thermostat? It's a couple bucks and it's not worth the risk to use an old one.
                        Because carrace. I'll buy a new one it doesn't matter to me.

                        Originally posted by NitroRustlerDriver
                        Your cooling fan isn't accidentally set to blow AWAY from the engine (forward), is it? Had a friend do this with a mechanical fan. Took him forever to figure out why the car was over heating.
                        Nope it's blowing air towards and through the rad, setup fine.
                        Originally posted by TSI
                        ♫ Rust flecks are falling on my head...♫
                        OEM+

                        Comment

                        • 328ijunkie
                          Forum Sponsor
                          • May 2007
                          • 3961

                          #13
                          Your biggest problem is the M42 radiator and the fact its too small and its a mother Fer to bleed properly.

                          Check Us out on Facebook
                          Needing a harness adapter or wiring help? Check it out: also have 24v motor mounts, E30 M3 covers and E36 ECU mounts!
                          Full Product Line Tuning
                          OBD2 Tuning Available! OBD2 E36, S54 Swap, S62 Swap, etc: tuning@MarkertMotorWorks.com Dyno Thread

                          Comment

                          • lolcantturn
                            R3V Elite
                            • Oct 2010
                            • 4588

                            #14
                            People run M42 rads all the time thoughhhh.

                            It is a bitch to bleed well though fuck.
                            Originally posted by TSI
                            ♫ Rust flecks are falling on my head...♫
                            OEM+

                            Comment

                            • nrubenstein
                              No R3VLimiter
                              • Feb 2009
                              • 3148

                              #15
                              Did you elevate the front end while bleeding it? I'd start there.

                              the M42 radiator sucksass, but it doesn't suck so much ass that you can't drive the car with it.
                              2006 GMC Sierra 2500HD 4WD LBZ/Allison
                              2002 BMW M3 Alpinweiß/Black
                              1999 323i GTS2 Alpinweiß
                              1995 M3 Dakargelb/Black
                              - S50B32/S6S420G/3.91
                              1990 325is Brilliantrot/Tan
                              1989 M3 Alpinweiß/Black

                              Hers: 1996 Porsche 911 Turbo Black/Black
                              Hers: 1988 325iX Coupe Diamantschwartz/Black 5spd

                              sigpic

                              Comment

                              Working...