My m50 is pinging. Running out of ideas.

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • 328ijunkie
    replied
    its 3.5 bar with no vacuum on it.

    Leave a comment:


  • ak-
    replied
    Makes sense to me..
    My m20 floats at a constant 3bar, so I don't see why your 24v shouldn't be at 3.5

    Leave a comment:


  • Wishno87
    replied
    Anyone?

    Leave a comment:


  • Wishno87
    replied
    Originally posted by Wishno87
    So this is where my fuel pressure is at and it did not move as I revved it up.
    So I replaced my fpr a few weeks ago. Of course that did nothing. I did notice that my fpr said it was supposed to run at 3.5 bar though. If my car is running at 3.1 bar and the engine calls for 3.5 bar could that be the problem?

    Leave a comment:


  • pmat
    replied
    Originally posted by Ryann
    Why would faulty VANOS cause this?
    When the VANOS piston seal is worn, the intake cam cannot advance for more cam overlap. This has the effect that internal-EGR (exhaust gas recirculation) is reduced. With less recirculated exhaust in the intake stroke, you will have more air and fuel in the cylinder, but the absence of exhaust gas will increase the combustion rate. Since the spark timing occurs based on the assumed exhaust/air/fuel in the cylinder, the combustion will now be too fast and cause pinging. The pinging is detected by the knock sensor, which in turn retards the ignition with loss of power as a result.

    Leave a comment:


  • Dj Buttchug
    replied
    my shit pings still too. Im over trying to fix it. Im gonna mash it till it blows up.






    Whatever.

    Leave a comment:


  • Matt-B
    replied
    damn... :(


    I hope, you can track this down, is it possible, you have bad lifters, or a related head issue?

    Leave a comment:


  • Wishno87
    replied
    Well it appears the rebuilt vanos and new cam sensor did nothing. I will still install the rebuilt vanos on the e34 though just because it probably could use it so I will report back with that.

    Also yesterday I installed a new ecu coolent temp sensor and new oil cap as well as swapped coil packs. Still nothing.

    Today I will swap injectors and fpr.

    Leave a comment:


  • Wishno87
    replied
    I ordered a new cam sensor to install while I'm replacing the vanos unit because you need to remove the vanos solenoid anyway. I couldn't find any ohm specs for the cam sensor though. Just the crank sensor.

    Leave a comment:


  • butters
    replied
    Damn, this sounds frustrating. I'm in just to see what happens, hope you can sort it out.

    Seafoam didn't do anything for me either; I had my motor rebuilt afterwards and the pistons and valves were still horrifyingly caked with deposits, though to be fair it was burning significant oil. Also I didn't experience any pinging despite a that and a bad HG / poor compression.

    Originally posted by Austin!
    I would check resistance on the cam sensor, just to be safe.
    I would check resistance on all the things just to be safe. Seems like it could be one of those terrible electrical gremlins we all dread.

    You mentioned it was different/worse on a different ECU - does it change much when you unplug the battery for awhile then try again? I wonder what the adaptations are doing, maybe that holds a clue.

    Leave a comment:


  • e30austin
    replied
    I would check resistance on the cam sensor, just to be safe. Good luck! You'll want to drive it a lot more after you do cams and a tune.

    Leave a comment:


  • Wishno87
    replied
    Knock sensors are new. Haven't touched the cam sensor. Will do the coolent temp sensor next time I pull the intake. At this point I'm betting on the vanos. Replacing it next weekend along with some s50 cams and squid tune.

    Leave a comment:


  • e30austin
    replied
    It would have needed replacing eventually. Did you ever check out your knock sensors? How about cam sensor?

    Leave a comment:


  • Matt-B
    replied
    Originally posted by Austin!
    I knew it wouldn't.

    How did the rest of your sensors check out?
    Should have said something...

    Leave a comment:


  • justin_l_
    replied
    Originally posted by Wishno87
    My podi is setup for it but I haven't bought the wideband yet because I can't get any of the rest of the gauge working.
    I got the one I have all set up if you think I can help send me a pm.

    Leave a comment:

Working...