M50 swap that will blow your mind.

[Zesty Bonanza]

Hi Noshow20x96,

Does your car have ABS? My car does not have ABS and the e30 master cylinder had 3 lines connected; two for the front left and right, and one for the rear that splits in the back. I'm trying to figure out how to use the e90 master cylinder that has only two connectors for lines. Do you have any advice on splitting the lines?

Thanks,
Ben

[Noshow20x96]

Would the e90 clevis pin work?

The e90 pin doesn’t have the extended cutout for the spring to return the pedal.


Sent from my iPhone using Tapatalk Pro

[onlyindef]

Would the e90 clevis pin work?

[reelizmpro]

Oh, that's the E90 booster as well?

Yes.

[The Dark Side of Will]

Oh, that's the E90 booster as well?

[reelizmpro]

E90

[The Dark Side of Will]

Finally have some pics to share...

Here's my setup using adapter fittings I had custom made at a local brake shop. Also found the metric bubble flare unions and tees at a local aircraft supply shop. This makes it all plug and play. I decided to go this route just incase I wanted to switch back to the stock style master with a 944 booster or something.

Initially, I went with the E34 530i reservoir setup but didn't feel comfortable converting the plastic brittle hoses to rubber reinforced. I found the rubber reinforced hose was a little too large for the E34 setup. They slid on/off a little too easily for me so I ordered up the 2002 reservoir (BTW, this is the same setup M3 guys running the DTM carbon airbox run) and direct mounted it to the master. Instead of running a longer clutch hose, I used one of the elbows to extend the existing hose. I didn't see the purpose of remote mounting it since it fits right on top of the master and I can still use the level sensor.

Is that an E83 MC?

[Staszek]

Brand new 944 porsche booster lasted us just fine the last 62hrs in endurance racing and is still just fine.


if you buy some used crap like many r3vtards it will die


im interested for a comparison between the e90 & x3 vs stock or stock + 750il master with rx7 front calipers.


the change to RX7 front brakes and VW rotors sent too much brake bias frontwards; wondering if there is a more rear biased oem modern bmw brake master that will go on a E30


from looking at modern bmw' on the lift at my local indy shop in for service it seems that the new x3 and others wear out rear brakes alot faster than older cars

I ended up going with a brand new 944 Booster and brand new E30 master.

The E90 one would not fit the S54 without extensive modification to the airbox.

[reelizmpro]

Finally have some pics to share...

Here's my setup using adapter fittings I had custom made at a local brake shop. Also found the metric bubble flare unions and tees at a local aircraft supply shop. This makes it all plug and play. I decided to go this route just incase I wanted to switch back to the stock style master with a 944 booster or something.

Initially, I went with the E34 530i reservoir setup but didn't feel comfortable converting the plastic brittle hoses to rubber reinforced. I found the rubber reinforced hose was a little too large for the E34 setup. They slid on/off a little too easily for me so I ordered up the 2002 reservoir (BTW, this is the same setup M3 guys running the DTM carbon airbox run) and direct mounted it to the master. Instead of running a longer clutch hose, I used one of the elbows to extend the existing hose. I didn't see the purpose of remote mounting it since it fits right on top of the master and I can still use the level sensor.

[eternal24k]

Speaking of diaphragms, how much rotation on the clevis is ok? Mine rotating a bit here and there during handling

[Wanganstyle]

This is one of the reasons why I went with the e9x booster and I kept reading that the diaphragms on the 944 boosters break internally, very common.


Sent from my iPhone using Tapatalk Pro

Brand new 944 porsche booster lasted us just fine the last 62hrs in endurance racing and is still just fine.


if you buy some used crap like many r3vtards it will die


im interested for a comparison between the e90 & x3 vs stock or stock + 750il master with rx7 front calipers.


the change to RX7 front brakes and VW rotors sent too much brake bias frontwards; wondering if there is a more rear biased oem modern bmw brake master that will go on a E30


from looking at modern bmw' on the lift at my local indy shop in for service it seems that the new x3 and others wear out rear brakes alot faster than older cars

[jwal]

I think the E90 booster would be the same, you can either use a new pin or cut and thread (much like a Porsche 944).
That clevis is the original from the E30 booster so I could use the E30 pin.

I think you could use the modified pin without threading the X3, you just do not have any adjustability (the X3 is slightly longer).

Ok, so in that case, the only real difference is the master cylinder? Any idea if they have different bores or if just the port locations are different?

[eternal24k]

Awesome, thanks so much for your work! So it looks like the X3 booster is slightly more convenient to use. Not having to get a pin made or modify the lines is definitely preferred. That clevis on your booster looks like a rough block. Is that the stock one or did you have one made for an earlier V8 booster or something?

I think the E90 booster would be the same, you can either use a new pin or cut and thread (much like a Porsche 944).
That clevis is the original from the E30 booster so I could use the E30 pin.

I think you could use the modified pin without threading the X3, you just do not have any adjustability (the X3 is slightly longer).

[jwal]

test fit my X3 booster. I ended up shaving and threaded the rod to keep adjustable and use the E30 pin.

Awesome, thanks so much for your work! So it looks like the X3 booster is slightly more convenient to use. Not having to get a pin made or modify the lines is definitely preferred. That clevis on your booster looks like a rough block. Is that the stock one or did you have one made for an earlier V8 booster or something?

[eternal24k]

test fit my X3 booster. I ended up shaving and threaded the rod to keep adjustable and use the E30 pin.