Megasquirt Timing and Fuel Map Thread

[Digitalwave]

On TunerStudio dashboard you can add a gauge that shows you sync loss count. That's the easiest way to see if you are losing sync, besides the tooth logger. It should basically have no sync loss except 1 count every time you "burn" a change to the ECU while it's on. IE if you have the car on for 10 minutes and you burn changes 3 times to the ECU, it should show a sync loss of 3. Anything more and you have an issue.

[justinpirie]

I’ve found a fuel pressure gauge or sensor is the best place to start there. Don’t swap pumps until you’ve verified it’s the culprit.


Sent from my iPhone using Tapatalk

[Joegreen02]

On TunerStudio dashboard you can add a gauge that shows you sync loss count. That's the easiest way to see if you are losing sync, besides the tooth logger. It should basically have no sync loss except 1 count every time you "burn" a change to the ECU while it's on. IE if you have the car on for 10 minutes and you burn changes 3 times to the ECU, it should show a sync loss of 3. Anything more and you have an issue.

Gonna try this out right now. Thanks


Sent from my iPhone using Tapatalk

[Joegreen02]

I’ve found a fuel pressure gauge or sensor is the best place to start there. Don’t swap pumps until you’ve verified it’s the culprit.


Sent from my iPhone using Tapatalk

I was planning on putting the bigger pump anyway so. It's already done now. Lol

Also doesn't appear to be any sync loss


Sent from my iPhone using Tapatalk

[justinpirie]

I was planning on putting the bigger pump anyway so. It's already done now. Lol

Also doesn't appear to be any sync loss


Sent from my iPhone using Tapatalk

Cool. How is the power above 5000 now. Injector Duty cycle?


Sent from my iPhone using Tapatalk

[Joegreen02]

Cool. How is the power above 5000 now. Injector Duty cycle?


Sent from my iPhone using Tapatalk

It pulls hard up to 5000 power is great. After that she is still floundering doesn't fall on its face but it's still missing. Sounds like a wet distributor cap so I've got a new cap and rotor I'm about to through in there too. Edwardo estimated 170ish to the wheels once the fuel supply is there. I'm doing the injector swap now.




Sent from my iPhone using Tapatalk

[Joegreen02]

Megasquirt Timing and Fuel Map Thread

I don't know how to check duty cycle [emoji2357]

Gonna have to figure out how to tell ms I changed injectors too. So there is that lol.


Sent from my iPhone using Tapatalk

[justinpirie]

I don't know how to check duty cycle [emoji2357]

Gonna have to figure out how to tell ms I changed injectors too. So there is that lol.


Sent from my iPhone using Tapatalk

In megalog!


Sent from my iPhone using Tapatalk

[Joegreen02]

Lol I did a log I'll have to look at it and see. I'm learning I'm learning


Sent from my iPhone using Tapatalk

[justinpirie]

Lol I did a log I'll have to look at it and see. I'm learning I'm learning


Sent from my iPhone using Tapatalk

Also you can put it on a TS dashboard. Hard to use while driving though.


Sent from my iPhone using Tapatalk

[Joegreen02]

Also you can put it on a TS dashboard. Hard to use while driving though.


Sent from my iPhone using Tapatalk

I'll try that too. This thing is gonna be a beast once I figure out if I'm going super charged or turbo. I'm still on the fence on that too


Sent from my iPhone using Tapatalk

[Joegreen02]

What needs to be changed for these injectors?


Sent from my iPhone using Tapatalk

[Joegreen02]

Megasquirt Timing and Fuel Map Thread

Look at this why is my timing going crazy here? What would cause that?

What is the max spark advance for these m20b25


Sent from my iPhone using Tapatalk

[Jaxx_]

you are hitting the rev limiter. If you look below it says SPK: revlim retard(deg): 2.7. It takes 2.7 degs from your base to get 34.3.

It's a 2 valve head with a little quench... 36-38-40 is probably in the realm of "correct" at WOT after 3k. To know for sure, you need a dyno, of course.



You need to change your required fuel in your general settings after changing injector flow rate. You also should change dead time if you have it available. It's not the end of the world if you don't have it. It's not as important as some people make it out to be

[Joegreen02]

you are hitting the rev limiter. If you look below it says SPK: revlim retard(deg): 2.7. It takes 2.7 degs from your base to get 34.3.

It's a 2 valve head with a little quench... 36-38-40 is probably in the realm of "correct" at WOT after 3k. To know for sure, you need a dyno, of course.



You need to change your required fuel in your general settings after changing injector flow rate. You also should change dead time if you have it available. It's not the end of the world if you don't have it. It's not as important as some people make it out to be

The Rev limiter is set to 6300 though not 5750. I do have dead time available although I don't know what that is or how it should be manipulated only thing I could find on the injectors is they are 23.8 gph. I did reset that and I believe my problem with the cutting out to be the gap on the cps I'm gonna reset it tomorrow morning and I'll report back. If it clears up its back to the dyno to put down closer to 200!


Sent from my iPhone using Tapatalk