Originally posted by digger
View Post
Announcement
Collapse
No announcement yet.
Polyurethane motor mounts?
Collapse
X
-
I second the 95A poly mounts. Did them with the manual swap along with poly trans. A tad more noise but nothing I can complain about. It does make the whole car vibrate at certain RPMs idk why (like 3700 is just a significant increase and then it goes away at 3800).
Leave a comment:
-
I didn't notice much of an impact from switching from good condition stock engine mounts to 95A poly mounts. The car has a bit more vibration at idle, but otherwise it was indecipherable. It might also be because the rest of the car is already so "race car" that I just didn't notice (car is full poly or delrin everywhere in the suspension). I have heard that the trans mounts make a really big difference in NVH so I opted to run the thicker stock 23711175424 rubber mounts with a reinforcing cup and been pretty happy.
Leave a comment:
-
probably easier to say genuine BMW parts or aftermarket as that's what i'm referring to.
in the case of engine mounts the genuine are like $80 and the others about $8 and the genuine are much better. not 10x better but engine mounts are a PITA to change so you want the best and the lowest chance of delamination
Leave a comment:
-
It's so confusing. In the industry, OE is supposed to mean what came in the car from the mfgr as installed on the car when delivered. Once the part is replaced, it's not considered OE, even if the replacement part came from the auto maker. OEM means the same mfgr that made the original part makes the replacement (Febi, Bosch, Bher, Mhale, BMW etc). I tend to use OEM as the description for the part that is exactly the same as what was installed originally (NOT Rein, Uro, Elring etc)...
OEM stands for original equipment manufacturer. OE stands for original equipment. OE parts are the components of the vehicle as it's made in the factory – all of the original parts that the car was first built with. Once the car comes out of the factory, everything else is not an OE part.
Leave a comment:
-
Originally posted by zaq123 View Post
my '90 mounts were still in one piece after 25+ years....ugly one piece but still together.
What r u trying to say? isn't OE and OEM same thing?what do you run?
Leave a comment:
-
Originally posted by zaq123 View Post
my '90 mounts were still in one piece after 25+ years....ugly one piece but still together.
What r u trying to say? isn't OE and OEM same thing?what do you run?
Leave a comment:
-
Quality OE mounts are fine for a street car that sees occasional road tracks, even. When my car was a daily driver, I drove it to the track for HPDE events for about 2 years. It had the same mounts that came with the car (PO replaced them about a year before), and they didn't break until I lent the car to my pops to do his first track weekend - he hit the guad rail at Sebring.
The endurance race car had them for about 5 or 6 events (costs us modification points for solid mounts) until a driver hit a tire barrier at Daytona. That was about 6 hours into a 14 hour race, the fan hit the radiator (ultimately causing the engine to blow a HG much later). We would still be using rubber if it weren't for the fear of incidents. The solid mounts cost half the points of an aftermarket seat bar including heim joint adjustable links. Kinda backward rule IMO, sway bars decrease lap times far more than engine mounts.
Leave a comment:
-
OE m20 rubber engine mounts don't last anywhere near 20 years, and OEM ones are even worse
Leave a comment:
-
Originally posted by AWDBOB View PostIf the car is any sort of a street car I would not consider poly. There are HD rubber mounts available that give you the stiffness without the extra NHV, I’d snag those.
I know there will be a line of folks who disagree, I just don’t feel like poly offers much of anything over a good rubber bush.
Leave a comment:
-
If the car is any sort of a street car I would not consider poly. There are HD rubber mounts available that give you the stiffness without the extra NHV, I’d snag those.
I know there will be a line of folks who disagree, I just don’t feel like poly offers much of anything over a good rubber bush.
Leave a comment:
-
Polyurethane motor mounts?
Hello! I plan on replacing my motor mounts, as the passenger-side mount isn't exactly on speaking terms with the motor. It's just kind of sitting on it, off to the side. That said, I keep seeing polyurethane mounts for sale. How do they compare to the rubber ones, and should I consider picking some up?Tags: None
Leave a comment: