Announcement

Collapse
No announcement yet.

Air/ Fuel Ratio gauge

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #31
    Originally posted by NC325iC View Post
    ITS THE GOD DAMN GRAY ONE
    or is it the black one... i cant remember but honestly you arent going to get a reading, its just gonna go back and forth the entire time it will never rest on a readable number
    Thats what I was looking for, and it does rest on a reading when you give WOT, or at least my brothers Audi and RX-7 does.
    1985 325e 2.8 Turbo VEMS

    Comment


      #32
      no, it rests on a voltage. you can tell it's richer than 14.7, but you can't tell how rich it is. so it could be 14.6.. it could be 10. you have no idea. that's why they make widebands..
      Build thread

      Bimmerlabs

      Comment


        #33
        if you have an LC-1, just use that.
        1989 Turbo 325is
        87 ETA Dinan Stg 2

        Comment


          #34
          Originally posted by asubimmer View Post
          if the light comes on then your motor is already screwed. A gauge shows the pressure droping not just "ok" or "not".
          Huh? So you pull over and turn the motor off every time you engine slows becuase your oil pressure will drop?

          oil pressure will vary constantly depending on revs and temp. The idiot can actually come on at idle if its an older motor up to temp with a thin oil in it. Doesn't mean the motors fucked. Point is if the light comes on pull over and you should be right.

          Comment


            #35
            Originally posted by Borat View Post
            Huh? So you pull over and turn the motor off every time you engine slows becuase your oil pressure will drop?

            oil pressure will vary constantly depending on revs and temp. The idiot can actually come on at idle if its an older motor up to temp with a thin oil in it. Doesn't mean the motors fucked. Point is if the light comes on pull over and you should be right.
            you said it yourself that it changes....

            so why would you turn the motor off just cause it dropped a little? You would only turn it off if it drops BELOW a safe level.

            Say no to drugs newbz
            ///Alpinweiß II 24v 91' 318is, Alpinweiß III 99' 323i, 04' Yamaha R6 SE for sale, 00' VW GTi, 83' El Camino BURNED, 01' P71sold, 92' Miatasold

            Comment


              #36
              exactly, and the light indicates when the pressure is below a safe level.

              Newbz? ouch, guess I'll have to make more than 3 posts a week then.

              Comment


                #37
                as a measure of my newbness i have fucked up and posted twice.

                Comment


                  #38
                  Given that situation, I'd rather know when the pressure was nearing a dangerous level, instead of knowing when it had already reached said dangerous level.

                  Gauge FTW, light FTL.

                  "See, we're adding a little something to this month's sales contest. As you all know, first prize is a Cadillac Eldorado. Anyone wanna see second prize? Second prize is a set of steak knives. Third prize is you're fired."

                  Comment


                    #39
                    Originally posted by chbimmer View Post
                    if you have an LC-1, just use that.
                    Like I said I don't want to cut apart my harness, a cut harness is worth less $$... lol
                    1985 325e 2.8 Turbo VEMS

                    Comment


                      #40
                      you don't have to put it into your ecu. you can have 2 o2 sensors ;)
                      ///Alpinweiß II 24v 91' 318is, Alpinweiß III 99' 323i, 04' Yamaha R6 SE for sale, 00' VW GTi, 83' El Camino BURNED, 01' P71sold, 92' Miatasold

                      Comment


                        #41
                        Originally posted by asubimmer View Post
                        you don't have to put it into your ecu. you can have 2 o2 sensors ;)
                        he doesn't even have to do that - the LC-1 has a narroband output.
                        Build thread

                        Bimmerlabs

                        Comment


                          #42
                          Originally posted by nando View Post
                          he doesn't even have to do that - the LC-1 has a narroband output.
                          I am aware of that, he said that he didn't want to mess w/ the stock harness. Although you can leave the stock harness alone and wire it into the plug for the o2 sensor. I had an AEM wideband that also could put out a narrowband signal, but I only used it for about a month and then sold it.
                          ///Alpinweiß II 24v 91' 318is, Alpinweiß III 99' 323i, 04' Yamaha R6 SE for sale, 00' VW GTi, 83' El Camino BURNED, 01' P71sold, 92' Miatasold

                          Comment


                            #43
                            Originally posted by asubimmer View Post
                            Although you can leave the stock harness alone and wire it into the plug for the o2 sensor.
                            that's too obvious :p
                            Build thread

                            Bimmerlabs

                            Comment


                              #44
                              Originally posted by SamE30e View Post
                              Like I said I don't want to cut apart my harness, a cut harness is worth less $$... lol
                              Oh! Now it makes sense! You didn't want to cut apart your harness to install something that would give you a useful reading so you can resell the harness!

                              ....So you cut it apart to install a stupid gauge.

                              ....And you could have used the factory O2 connector for the LC-1.

                              Damn. So much for making sense.

                              Originally posted by SamE30e View Post
                              Actually no. I'm not using to to tune my AFM, I drive an e, it is the definition of slow. Nevermind I found the wire colour, you guys are useless.
                              Were just trying to give you a feel for your gauge and as helpful as it is. Hey, why not try tuning by r3v, find a thread that blunt posted in and every time someone says penis, thats one vote towards your car running rich, every time a homosexual reference is made, one vote towards lean. Might even be more effective than the gauge!
                              -Dave
                              2003 Lincoln Towncar | 1992 BMW 325iC | 1968 Cadillac Deville

                              Need some help figuring out the ETM?

                              Comment


                                #45
                                Ok I have a question then. I replaced my intake man. gaskets six months ago. One folded in the process and the car got worse and worse. It wasn't running too badly, but my a/frm started showing more and more lean.... I knew something was wrong b/c of the meter and low and behold.... It was right.
                                So what's so useless about that?
                                Yours truly,
                                Rich
                                sigpic
                                Originally posted by Rigmaster
                                you kids get off my lawn.....

                                Comment

                                Working...
                                X