If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
ASK ALL WHEEL/TIRE FITMENT QUESTIONS HERE - The Official Wheel/Tire Fitment Thread
16x7.5 et23 I want to fit atleast a 225/45. Late model e30. Will I need to roll fronts? Will I need spacers up front to clear struts? Rears have flares so not to worried about rear. Prolly use falken fk 452's or nexen n3000's. Its a lowered daily driver.
I have 16x8 et20 with 205/50 on now but looking to sell the wheels.
Thanks. I tried looking thru the thread but i must have a.d.d.
89 325i: 86 535i motor+trans, JE forged pistons, MLS head gasket, ARP head studs, Comp turbo, GoodNTight b34 turbo manifold, e30.de motor mounts, AKG 75D engine/trans mounts, custom 3" exhaust, intercooler, MS2PNP, Megan Racing Coilovers.
17x10 ET20 with 245/35/17 tire will it fit in the rear with just a rolled fender lip?
Or do I need much more massaging?
Even with a super-stretched 225/35 17x10s require a bit of a pull to work properly. I'd put 245/35 in the realm of "doesn't fit" but enough fender work could change that.
16x7.5 et23 I want to fit atleast a 225/45. Late model e30. Will I need to roll fronts? Will I need spacers up front to clear struts? Rears have flares so not to worried about rear. Prolly use falken fk 452's or nexen n3000's. Its a lowered daily driver.
I have 16x8 et20 with 205/50 on now but looking to sell the wheels.
Thanks. I tried looking thru the thread but i must have a.d.d.
Fits fine, no spacers. Note that those Nexens run extremely wide in that particular size (I test fit them once on my E30 on a 16x8 +20 wheel).
I would like the rims to sit as close to flush with the guards as possible. I have a mate with a guard roller so rolling guards wouldnt be a problem id rather not pull them tho.
The car will be on bc coilovers and it will be 70mm off the ground at its lowest point.
I would like the rims to sit as close to flush with the guards as possible. I have a mate with a guard roller so rolling guards wouldnt be a problem id rather not pull them tho.
The car will be on bc coilovers and it will be 70mm off the ground at its lowest point.
cheers
Option 1: 20mm front spacers to clear the struts. F: 205/40. R: 225/35.
Option 2: 205/40 all around. Probably toss a 5-10mm spacer on later to taste (even out front-rear stagger a bit on your early arches).
I have 17x 9s and the offset is et22. Does anyone know if these will fit? As far as the front and back? I'm pretty low but I was planning on stretches too
I have 17x 9s and the offset is et22. Does anyone know if these will fit? As far as the front and back? I'm pretty low but I was planning on stretches too
Yes, I know. :p You'll need 8-10mm spacers to use those on the front axle, while the rears need nothing.
found some wheels that r 16x8 and r et 25 wanted to no if i can run 225 45 16 or even 235 45 16 in rear ..and 215 45 16 in front what do u think or should i go 17 and if so what offset to get im trying to get the widest drag radial tires in back as possible ..as soon as u give me the ok i am going to by the wheels,they r the
16X8 VARRSTOEN V4 4X100 +25 SILVER..let me no thanks
Comment