I need a new gear ratio

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Brandon12V
    E30 Fanatic
    • Feb 2008
    • 1318

    #16
    I'd say he's pretty damn close. I sit around 3200 with my 3.73 @ 70mph.

    Originally posted by Ryan...
    It now emits a beautiful blue-ish yellow/green smoke from the exhaust?? No idea what would cause that color, but I assume its good.

    Comment

    • nando
      Moderator
      • Nov 2003
      • 34827

      #17
      80mph with a 4.10 is only 3700
      Build thread

      Bimmerlabs

      Comment

      • Rsully70sev
        R3VLimited
        • Sep 2010
        • 2391

        #18
        Well if that's the case, it's a nonissue. I'm pretty sure my numbers are correct. I'd say 80-85 is more in the 3700 range now that I think about it though.

        I drove it over the weekend up to Mendocino, and all I could think about the entire drive was "hmm, 4k cruising, I'm fucked if my belt brakes or something." I guess I'm just used to a sixth gear and lower rpms.

        As for gas, it wasn't anything I noticed, just sort of logic. I just figured after a certain point it was wasting gas, if that point is 3k then my gears are all good in my book. I think I was just being a little paranoid, I havent driven the car in a few months.

        Comment

        • Wh33lhop
          R3V OG
          • Feb 2009
          • 11705

          #19
          Simple ratios, guys. 80 with a:

          3.73 is 3400rpm
          4.10 is 3750rpm
          3.46 is 3150rpm
          3.25 is 2950rpm
          2.93 is 2650rpm
          paint sucks

          Comment

          • Jesse30
            No R3VLimiter
            • Jan 2007
            • 3936

            #20
            Originally posted by Rsully70sev
            Well if that's the case, it's a nonissue. I'm pretty sure my numbers are correct. I'd say 80-85 is more in the 3700 range now that I think about it though.

            I drove it over the weekend up to Mendocino, and all I could think about the entire drive was "hmm, 4k cruising, I'm fucked if my belt brakes or something." I guess I'm just used to a sixth gear and lower rpms.

            As for gas, it wasn't anything I noticed, just sort of logic. I just figured after a certain point it was wasting gas, if that point is 3k then my gears are all good in my book. I think I was just being a little paranoid, I havent driven the car in a few months.
            you're pretty much fucked if your belt breaks regardless. interference motors like to bang valves. just keep up on your timing belt and you wont have to worry.

            you seem very paranoid. almost every post is you worrying about your car, just chill. this is coming from someone who beats the ever living crap out of their e30's, swapped or not. these cars are pretty robust.

            Comment

            • Stoner Sam23
              Advanced Member
              • Apr 2010
              • 186

              #21
              I put a 4.10 in my 325 and i commuted dailly with it. who cares about gas mileage its fun

              Comment

              • Sagaris
                R3VLimited
                • Sep 2009
                • 2243

                #22
                I had a 4.10 G260 M20B25 with 195/60/14 tires. I had always thought that the freeway RPM would be the problem, but it actually wasn't. The big problem was how ridiculous 1st gear was. Sometimes had a hard time deciding whether to start out in 1st or 2nd from a stop. I would be in 2nd gear before I hit the middle of an intersection.

                I am planning on 3.73 with the same tire size. I think it will be fine then.
                It would be great to have an extra tall 5th gear for cruising though.

                Comment

                • nando
                  Moderator
                  • Nov 2003
                  • 34827

                  #23
                  do you shift at 1500rpm or something? :p
                  Build thread

                  Bimmerlabs

                  Comment

                  • Sagaris
                    R3VLimited
                    • Sep 2009
                    • 2243

                    #24
                    750 +/- 50 rpm

                    Comment

                    • nando
                      Moderator
                      • Nov 2003
                      • 34827

                      #25
                      uhm?
                      Build thread

                      Bimmerlabs

                      Comment

                      • Sagaris
                        R3VLimited
                        • Sep 2009
                        • 2243

                        #26
                        or maybe those are the idle adjustment specs

                        Actual shift RPM was not absurd though, something between 2000-3000. I just remember feeling like an 18-wheeler pulling away from a light.

                        Comment

                        • bmwguy325is
                          E30 Fanatic
                          • May 2011
                          • 1262

                          #27
                          I run a 3.64 rear gear and try to keep the tire Dia to 23.5-24 inches. Tire size can change your highway cruise RPM by a couple hundred rpm.
                          The 3.64 is a good compromise. I have a 87' is and with the exception of this stump puller 1st gear with a raised RPM limit I can to 60 in 2nd and 90 in third. And the car gets decent millage at cruise RPM and 70mph.
                          Having know several people that hade these cars new in Germany they used to cruise in them at 100-110 for hours at a time with no adverse side effects.
                          sigpic"If one does not fail at times, then one has not challenged himself." -Ferdinand Porsche
                          The ugly car: http://www.r3vlimited.com/board/showthread.php?t=209713

                          Comment

                          • Blackout
                            R3V Elite
                            • Apr 2011
                            • 4125

                            #28
                            I have 3.73 and i can barely cover any distance in 1st and 2nd gear.
                            It is freakkin lame. And there is no pull in 3rd and 4th gear either.
                            The only time the car pulls is in the 5th gear.
                            What is the point of this? I'd rather drive an automatic.
                            Shifting from Neutral to 1 to 2 to 3 to 4 is worthless.
                            I seriously want to swap for a 2.xx Diff.
                            And yes, i too am at 4K rpm at 80mpm.
                            » PARTS FOR SALE
                            » TRANSACTION FEEDBACK

                            Comment

                            • nando
                              Moderator
                              • Nov 2003
                              • 34827

                              #29
                              Originally posted by Blackout
                              And yes, i too am at 4K rpm at 80mpm.
                              ^ no you aren't. not unless your tires are like 2" undersized in diameter
                              Build thread

                              Bimmerlabs

                              Comment

                              • nando
                                Moderator
                                • Nov 2003
                                • 34827

                                #30
                                Originally posted by Sagaris
                                or maybe those are the idle adjustment specs

                                Actual shift RPM was not absurd though, something between 2000-3000. I just remember feeling like an 18-wheeler pulling away from a light.
                                just bury it off the line. you'll feel differently. :D
                                Build thread

                                Bimmerlabs

                                Comment

                                Working...