I know that even when I finish what I want there will be other things to do, getting the interior reupholstered at some point being one (it's fine now with no rips etc)
Thanks! I intend to keep up the attention to detail, probably why I'm very reluctant to pay for someone to finish it.
Touring M52B28 (another one from Ireland)
Collapse
X
-
Just read through the entire thread... Your attention to detail is second to none, we all want to see you make more progress!Leave a comment:
-
Looks like it's been over 2 years since I've posted an update! You missed nothing, as nothing has really progressed since the last post and probably won't for another few years (part time college to blame for that...)
Anyway, this happened a long time ago in 2012...

Rented a van earlier this year in Feb after a visit a week earlier (thanks Gavin for moral support)


Finish on a dusty bonnet

Unfortunately my patients had run out and most of the parts left (except the bonnet) are unpainted and back in the shed. I think the plan is to keep tipping away at her over the summer and eventually some day drive it to a paint shop to see about getting someone else to finish painting the remainder of the parts or worst case re-paint the whole car again.
She's not looking as bad now, I tried to wash it a little in the shed so some dust is gone since.

Interior

Leave a comment:
-
Pulled the pair of wires for the gauges senders today and re-did them on their own with a new third wire added in for warning light.

And engine loom all taped up again with the extra wires branching of just before the ecu plug
Leave a comment:
-
None recently, the painter,still, has the trim and what not in his paintshop.
I can't remember if it's in this thread or not, I got a pair of 2dr popout windows and pretty much replicated how this worked and then adapted the same principals to fit with the touring glass. The main problem is the trim is NLA from BMW I managed to get one and luckily the other was still useable. I also broke the glass removing it so be careful and take your time or get it removed professionally.Leave a comment:
-
MORE! Any progress with the pop out rear glass? I have a touring here in the US, and I am hesitant to take the car apart for the sake of finding out whether or not the retrofit is possible.
I can't get things like the trim clips and the quarter glass here. :(
Wonderful work, keep at it.Leave a comment:
-
Thanks buddy! Took a bit of elbow grease but was worth the effort! Surprising how clean it got also! Unfortunately it's gotten a little dusty over the past year but I'll clean it again one final time before it goes back in the bay.
Not really made much progress, been working to much and not spending time at the touring since the summer.
At some point last year I started extending all the wires running around the engine bay, I wanted to hide them as much as possible but not go to crazy.
Using an old loom I extended all the wiring with the same color cable. Then came to my senses after realizing I potentially had up to 3x solder joins that could fail and went ahead and ordered a load of cables and various crimps so I could tack this mess:

In the end I pulled all the original cables going to fuses and replaced them with extra long new cables with the right ends crimped on and sloted back in place. A few cables ran into the car and those were solder joined inside the fusebox and had some heatshrink applied.
The plan was to separate all the wiring going to the passenger and driver side and route them both separately as can be seen below:

That was then stuffed through a pair of holes into conduit on the inner wings and routed to the front of the car where it exits under the front slam panel on either side




Conduit and 90deg elbow I used on both ends to protect it from the elements as much as possible (apparently the elbows are water proof)

This all took me months and many weekends, everytime I spent a couple hours at it most of the time was spent re-tracing my steps and making sure I didn't miss any cables or got things mixed up. Eventually I pulled it all through the conduit which turned out to quite difficult! I pulled out all the wires and after speakign to a friend he recomended I use wire pulling lube
That took a bit to arrive but it made everything about 100x easier. In the event I missed a wire I left one long redundant wire in the loom which runs to/from the fuse box so I could tape wire to this and pull it through if I have to (which I have with a few cables since).
I'm also fitting VDO gauges which needed wiring up neatly. Not liking many of the t-pieces and adapters and what not available I ended up drilling a hole in one of the vanos banjo bolts and threading it for the temp sender. The pressure sender is still on an extension/adapter but at least I now don't have another adapter on this for temp. Both wires were fed through the engine loom, crimped and I used some heatshrink to color code the wires, pics below of it in place:

And the bit of engine loom I fed both wires through:

Over the weekend I'll probably undo all the above after realizing the second terminal on the pressure sender is for a warining light, which I might as well also make use of.
Thats all for slow progress
Last edited by Jozi; 03-17-2016, 04:22 PM.Leave a comment:
-
Cheers guys for the encouraging words!
Not much of an update but have started unpacking all the boxes and sorting through everything and trying to keep it organised on the rack or in boxes. I might get it all put away over the weekend and then I can get back at working on the touring again.
Leave a comment:
-
The zinc plating looks amazing, very nice! This motor is going to shine. Also yes, you have a 323i flywheel there. 13lbs confirms it.Leave a comment:
-
holy shit this is a long term project.
I love the zinc plated stuff everywhere. very satisfyingLeave a comment:
-
hey man, i love this thread. Plz keep it alive, dont give up on this projectLeave a comment:
-
This thread is long over due an update! Not much has happened this year between it being to cold, no interest/motivation and not going home most weekends to work on the touring not a lot has happened!
The good news is the touring now looks like this:

Few bits stored inside for transport:

An E30 equipped Alfa 147:


A few weeks ago myself and a member e30owners got ourselves a shed, it's only about 15-30mins drive depending on traffic from where I live in Dublin. The past two weekends I've (with a lot of help from the brother) done a bit of tidying up around and gathered parts and so far done two runs with the Alfa stashed full of E30 parts. I still need to get the E30 trailered down (proving to be expensive or difficult) which I hope to sort this week or asap so I can get cracking on.

"Storage room" is slowly turning back into a spare bedroom:

Few pics I found which I hadn't up loaded yet from last December, some other little bits and pieces have been done but nothing major.
E30 323i (I think) flywheel I got a few years ago, had it skimmed ages ago, needed a little cleaning with a wirebrush.



There isn't much I can do with out the touring being here other than some small bits and pieces in preparation. Started polishing the glass this evening, plan is to get them nice and clean and then treat them with some sort of rain repellent on the outside and anti fog on the inside.

Once the glass is all polished and coated my first priority is to get it all fitted and wash her cause it looks nasty!Leave a comment:

Leave a comment: