Touring M52B28 (another one from Ireland)

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Jozi
    replied
    I just had a few days of tidying up some lose ends and loads of small job which meant I finally made some progress by the end of today :D

    Few touch-ups to the front struts and disc backing plates


    I had to get custom handbrake cables made as a result of chopping up 10cm of the metal tube under the car in which it runs. From what I remember I bought a cable in a motor factors and got a company to make me a pair exactly the same only with 10cm added to the outer cable. All well and good till I went to fit it, the little eye let was to wide and to wide Some minutes later on a bench grinder and 40mins in the zinc tank and she fits


    When I pulled of the bearing from the struts I found this


    Pretty bad I thought for a pair of bearings with no miles on them that has been on a car that was sitting up. Treated them and painted up the worst of it with alloy wheel silver, came up lovely.




    I only realised today I forgot the backing plates, luckily I was able to pull the bearings of again, the nearly slid of.

    Rear discs were also a bit rust, cleaned them up with a wire wheel and some paint on the bells (I'll pull the masking tape of the brake surface when she's ready to go on the road)


    Diff painted up with 2x coats of hammerite after I ran out of spray paint, bit shiny but it will do, diff cover also painted with wheel silver. Just got to zinc the sensor plate and the 2x alen bolts for filling her up.


    And finally today with some help of my brother we got the lot bolted up under the car :dance:

    All thats left to do it tighten everything up to their torque value's set the camber/caster and a couple more small jobs but she's as good as ready for wheels to be put on.





    Front end also all bolted up and ready for wheels after all the bolts are torqued up right.


    I zinc plated the rear subframe brackets and painted them silver since I ran out of black, came out fine though.


    And here's a little something I've been working on as well

    Leave a comment:


  • Jozi
    replied
    Small update, didn't get as much done as I wanted to over the weekend. Ran out of paint and my handbrake cable doesn't fit

    Had the diff soaking in deox c for the past week with a little aquarium pump and heater. Came out nearly spotless with next to no rust


    Few little spots like this left but painted it up anyway




    Ran out of paint so only one coat, will do another coat next weekend and should be fine. Also got new bolts, yellow passivated them so they are pretty. Just need some washer and zinc the speed sensor plate and it can all go back together.

    Also got the diff cover cleaned up and painted



    Anyone know the correct orientation for the bush?

    Leave a comment:


  • Jozi
    replied
    For the past few weeks I've been prepping the arches for some undersealing and finally last weekend and this weekend I got it done. I had 4L of bilthamber dynax ub lying around dying to be used so, purists look away because this won't be to your liking :D






    And up close


    It's a slightly tacky finish, stuff will probably stick to it but I had my reasons for using it and there's no way it's gonna rust under there!

    Also, got a few more parts plated, few bolts were new and re-plated and the rest was cleaned up, de-rusted and replated


    The diff is in a big tub de-rusting, my attempt at eletrolysis didn't really work, think I used the wrong powder and I couldnt find the right stuff at the time so I've put a load of bilthamber dynax powder in the tub, a little water pump and a aquarium heater to help the process along.

    I've a few more parts to plate but I think I might have enough done to start putting subframe's back on the car next weekend :dance:

    Anyone know how to remove the top mount bolts from bc coilovers? The look pressed in. They have gone a little grubby and I want to plate them like the nuts on them

    Leave a comment:


  • Jozi
    replied
    Just a small update

    Got a start made on rebuilding the trailing arms, new kunifer brake lines, stainless brake nuts and stainless goodridge braided hoses



    Tools used


    One finished brake line


    And one trailing arm


    I have to zinc a few of the bolts that are used on the parking brake and get some new pads before I can finish the brakes of. Discs also need a bit of de-rusting and if my kit can manage I'll zinc plate them also.

    Leave a comment:


  • Jozi
    replied
    I've mostly been tidying up small bits here and there before I refit the subframes again. Plan is to also use Bilthmaber underseal in the arches and possibly a few other places under the car, it's a nasty looking black coating though.

    I've only so far fitted the front subframe and rack and the rear end can be bolted up once I have brake lines made and do up the clamps on the new cv boots.




    Anyone with BC Coils notice the rear rubber above the top mount perishing? I've had them maybe 2 years and 0 miles and the rubber is full of cracks.

    Leave a comment:


  • Jozi
    replied
    Little bit of progress this weekend, quite happy with what I got done for once :D

    Subframes were looking a bit worse for wear with dust from the paint shop and some paint chipped etc from being moved around. Decided to make use of some of bmw's own stone chip, more like a heavy rubberized paint than anything else, and treat the underside of the front subframe and the whole rear subframe with it, and some satin paint to make it look a little better. Both are ready to be refitted once I do the same with the trailing arms and wishones next time I'm home.





    Close up of the slightly textured finish.


    I also got the front of the car soundproofing started, made patterns using the old car as a template. Front of the car is done, will be adding more to some of the larger empty areas and I have another product I might use to cover the whole floor pan.



    Leave a comment:


  • Jozi
    replied
    Small update as progress has been nearly non-existant since starting a new job 5 weeks ago.

    Old shell is another step closer to being scrap ready now that I got the last of the shadowline trim removed last weekend and the rear quarter glass.






    And yes that one pice of glass missing


    Good thing I have spare from the red shell that has been restored.

    Leave a comment:


  • Jozi
    replied
    The zinc plating isnt to bad, once it works. I pretty much derust anything first, then leave it in some de-greaser and de rust again if bits were missing, then I leave it in the de-greaser that came with the kit for as long as possible, 2mins acid pickle and straight into the zinc tank after a quick rinse. That takes up to an hr depending on how much zinc you want, the gold/yellow colour takes 30seconds and I dry it with a hair dryer then.

    The seats are great, love them :D

    Leave a comment:


  • MyE30
    replied
    awesome build! those zinc plated bits are a great idea. it seems like a complicated process.

    i need to figure out a way to get a set of those Recaros.

    Leave a comment:


  • Jozi
    replied
    Been awhile since I did an update. I was getting the hang of the zinc plating and then it went to shit and just couldnt get a nice plate. I cooked up a new batch of electrolite and it's pretty much been working 100% since. For anyone thinking of doing it, you need patience and it's prob less hassle to let the pro's do it :p

    This is more or less what I've done so far


    Most of the bolts for the door lock, the lock brackets and bit are plated and a few other bolts from around the door also. Have started on doing the subframe nuts/bolts also, eccentric washers and nuts below for the rear arms. They were new but I decided to strip the coating from them and make them more shiny and maybe? more resistant to rust than what ever bmw had on them.



    I also gave the rack a good clean, new inner track rods (don't have or can't find outer ones) and new rubber boots, hardlines got some surface rust removed and a coat of paint, likewise with the spline and the two banjo bolts were zinc plated.

    Leave a comment:


  • Jozi
    replied
    Did these yesterday, mostly a trial run again, brake res bracket will be used as is though, I might possibly to all brackets and bolts in the bay gold passivated.

    Cleaned up as well as I could do them:


    Zinc plated


    And passivated

    Leave a comment:


  • Jozi
    replied
    Not much of an update really (being far lazier than I should be) but I do have some work in progress things.

    I wanted to get the doors built up but I couldn't let myself use the old grubby catches that go on the door shuts. So I came up with a plan:



    Plan was to take the old catches and pretty much ever nut or bolt that will be visible and zinc plate them myself. Couple of nuts, a bolt and a door catch to try it out on after bit of a going over with a wirewheel:



    I started with the lock catch thing:



    But I got my current a little high and burned the part. Second attempt but with another spare catch went much better, I still managed to burn it a little (user error) but up until that point it looked to be going real well! No pics of it but I do have this after yellow passivating it



    I also tried it on a bolts, as expected zinc won't coat the rust but it still came out quite well:



    And here's both compared to an original catch from one of the shells (it was actually in pretty good condition considering)




    A little more testing to do before I plate the parts that will go back on the car but so far I'm pretty happy with it!

    Progress-wise, it's been slow having to do one thing before I do another etc...

    So far I've pretty much got everything cavity waxed, sills will be done a 3rd time and I also have to do the subframes and some other parts.
    The loom is in the car but hasn't been routed around because I needed the holes for the cavity waxing.

    Leave a comment:


  • Jozi
    replied
    Not a clue, Irish maybe? He was either really sleepy or half dead when I took care of him

    Leave a comment:


  • Hooffenstein HD
    replied
    Originally posted by Jozi
    Also met this little fella when I removed the speaker grill
    European Wasp? Kill it with fire.

    Leave a comment:


  • Jozi
    replied
    Thanks Klasse. Just had a look for your thread, she looks pretty clean! Enjoy the build!

    --- edit ---

    Nick, I badly labelled the engine loom and spent ages trying to work it out :p I couldn't have just pulled the main loom without labelling it all, I'd have burned the lot down before figuring out where it's all mean to go!

    Leave a comment:

Working...