Touring M52B28 (another one from Ireland)

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Jozi
    replied
    Thanks guys. That wiring is the easy stuff, the wiring around the bay is going to be a pain especially if I forget something and have to re-wire it again!

    --------------------------------

    Things have been quiet on the touring front for the last while. After a few setbacks and holdups I finally got bolting up some of the vapour blasted parts. While those were being done I also had what ever brackets and nuts/bolts I could find sent of for powder coating and zinc plating (the later being one of the holdups...)

    Still piecing things back together bit by bit, loom is just loosely sitting on the engine


    Never mind the grubby bolts for the damper thing, they will be replaced with shorter ones after it gets a clean up.


    All the alloy bits came up like new


    I thought the PS pump was black it was that dirty when I got it


    New water pump and stat housing also got a quick clean as they had gone white from sitting up the last year


    Replated studs



    Some of the other bits I had plated




    Also undersealed the front crossmember with Bilthamber UB. I previously used this in the arches and brushed it on, for what ever reason I didn't think of it at the time but using a roller gives it a slightly nice looking finish.



    Anyone know where these two studs belong?

    Leave a comment:


  • CorvallisBMW
    replied
    Nice! That wiring looks intense.

    Leave a comment:


  • zumjosh
    replied
    Looking great. I've read this thread through several times already. Keep up the great work.

    Leave a comment:


  • Jozi
    replied
    Not much to update really, have kinda lost a bit of interest for different reasons. Forgot I had these photo's on my camera.



    The white stuff is just carpet underlay which I'll be using as a decoupling layer between the car body and the sound deadening I'm using. I'm not sure if I'll be covering everything but at least I'll be doing behind the dash, under the rear seats and the boot area.



    I also had a few parts from the engine vapour blasted, they look as good as new if not better! I have them all well soaked in ACF50 which should keep them from getting corroded again!



    Anyone looking to use/buy reinforcement plates for on a touring, they need a little modification to be made fit.

    Leave a comment:


  • Jozi
    replied
    Gave the inside of the car a bit of a clean last weekend and started on the loom.

    I did my best to keep it all neat when removed from the old car and I rolled up each loom run after I put it into the new shell. It didn't work out though I spent a good while untangling various parts of it while laying it out inside the front of the car.

    The rear end for the most part is in, it need clipping together here and there but it should all be in the right place.


    Front is still a bit of a mess, looms run where they should but arent tied down with anything clips or what not.


    I'll try sort out this mess and work from there next time


    Few things I'm unsure of, are these bullit connectors meant to be there, they both have a wire coming out of them with a connector on the end


    This plug is close to the fuel tank under the rear bench, driver side, I've not got a clue what it plugged into anymore?


    Does anyone know which way BMW routed the battery to boot cable in the 324 or 325ix tourings? Should there be anything other than the standard wiring cover and what happens the wires running along the rear arch behind the trim panel?


    This mess here will also need tidying up over the next few weeks

    Leave a comment:


  • Jozi
    replied
    Quick update with some stuff from last week, back working to just get the weekends at it from now on :(

    This here is the reason I started zinc plating everything, the original ones just looked crap next to the fresh paint.



    I got the doors built back up as well, just need to cable tie the wiring to the door and a few other little bits.




    One of the rear motor's had seized, turns out that you can use the motors from a front winder. Just 2x screws, pull it of and fit it to the other.

    Anyone know if this looks right, wasn't sure which way it went back on.


    Decided to splash out on some goodies, M52 BBTB, Mishimoto silicone elbow and rear top mount reinforcement plates

    Leave a comment:


  • Jozi
    replied
    Small update, started cleaning the engine today, with looking about as good as I think I'll get it without stripping it all down and getting everything vapour blasted or using some other method to clean alloys.

    I used Frost Ali-Clean to clean everthing after a de-greasing. While it does work it doesn't seem to get it spotless, the rough area's come up better than the smooth areas. You also need to protect the alloy again or it will corrode in no time, I'm using ACF-50 after hearing good things about it.

    Before and after for one of the engine arms



    And just an after from the engine, it wasn't bad (started cleaning it before) but it had a bit of white corrosion over most of it.



    The exhaust side came up much better then the intake side. I'm debating doing the stat housing, oil filter housing, alternator and a few other parts myself or getting them vapour blasted.

    Leave a comment:


  • Jozi
    replied
    Slowly but surely things are coming together. I spent the last 4 days or so doing the brake and fuel lines.

    I didn't enjoy these 2 jobs at all and hope not to have to do them for a long time! I used kunifer hardlines all round with stainless braided lines and also stainless brake nuts.

    I had bought a new T-Piece which turned out to be imperial so I atacked the old one with the angle grinder and used it, should be fine anyway.



    Lines at the rear of the car


    Few small problems :( When I mocked up my ABS relocation I must have used the E30 servo, which I think isn't as deep as the Clio one


    With everything tightened up properly there's maybe 2mm between the two, might just have to shave a corner of the abs cover!

    I also have a problem with the servo and a brake line clip getting in the way of each other


    Dent the servo or shave a little of the clip? If I space the servo out I might not be able to bolt it up and it will foul the ABS unit.

    Another problem noticed when doing the brake lines is that my diff isn't centred, is this normal, should I be worried? I couldnt seem to move it to the centre when I tried.

    I also got the fuel lines installed but no pics apparently, just need to trim them in the back and by the tank next tiem I'm home.

    Anyone know can the tank go on with the subframe in place or does it need to come off?

    I'm also missing the 2x pipes that are supposed to run over the top of the tank if anyone has them?

    Leave a comment:


  • Jozi
    replied
    Originally posted by DirtyDozen

    Have not seen someone do this in a long while, Very awesome!
    Easiest way to work on her, only cost around 150-200e for the metal and casters (which were expensive!) was well worth it!

    Originally posted by Roysneon
    Are you doing pop outs?
    Going to try anyway! I think I need a different window seal as the 2dr one pushes the glass out further than I would like, unless the whole lot pules it in and compresses the rubber enough to make it flush.

    I had a buddy measure the distance between the up stand for the glass and the edge of the quarter and the saloon has a but more width.

    Leave a comment:


  • Roysneon
    replied
    Are you doing pop outs?

    Leave a comment:


  • DirtyDozen
    replied


    Have not seen someone do this in a long while, Very awesome!

    Leave a comment:


  • Jozi
    replied
    Don't let her rot, just creating more work and hardship for yourself!

    Leave a comment:


  • AWDBOB
    replied
    Man oh man do I wish I could take on another restoration project like this.

    I'm secretly letting my iX rot so I can do this in the future.

    Leave a comment:


  • Jozi
    replied
    Originally posted by markt51
    damn you seem to be as anal/ocd/methodical as me. This is how i will be going about my build. Every bolt, nut, and surface gets cleaned and painted. Truly a pleasure to read through to far.
    Thanks very much for the kind words. I think it may have gotten slightly out of hand, I never setout to do it all this way but I wouldn't be happy otherwise!

    Leave a comment:


  • markt51
    replied
    damn you seem to be as anal/ocd/methodical as me. This is how i will be going about my build. Every bolt, nut, and surface gets cleaned and painted. Truly a pleasure to read through to far.

    Leave a comment:

Working...