This is coming along nice!
Sent from my iPhone using Tapatalk
Daily'ed Sedan build: 1986 325
Collapse
X
-
Great build thread!
Major respect for your willingness to just get in there and do the things! Bravo, my good sir!Leave a comment:
-
Yes! I'll get some pictures and details up soon. I'm taking some classes and they started up two weeks ago so things will slow down a little bit but hopefully not too much. Motor is still on the stand and will be for a bit as I accumulate more parts. The "to buy" list is as follows:
Clutch/flywheel kit- I'm looking at the ebay fx racing/sachs single mass conversion. I saw kronus used it in one of his cars so it's gotta be at least somewhat legit
Engine and drivetrain refresh bits and bobs (need an accessory belt and some other small gaskets)
Spal Pusher fan and associated wiring
Need to figure out what how to modify the stock e36 exhaust still (plan to change out that huge OEM muffler for something with a bit more grumble)
wiring harness modifications
dme flash
As much as I want to do the wiring myself, I don't think I reasonably have the time between the 70 hours of work and class I've got per week so I'll be sending the harness out to get modified for the swap. I've been shopping around a bit but haven't committed to anywhere yet. If anyone's got any recommendations I'm all ears.
I've also got some 5 lug swap/bbk stuff in the works :devil:
The pick and pull gods left a 318ti at my local yard two weeks ago and I snagged the trailing arms. I've been doing some brake bias calculations and If I'm not mistaken, e36m front brakes with non m e36 rear brakes gives a similar brake bias to stock e30, right? I think I got 7.6% front bias with e36m fronts and non-m rears. I may be totally wrong because I was using an SAE calculator and switching between a lot of tabs without writing anything down.Leave a comment:
-
Woo! Thanks dudes! I think I'm gonna hold off on s52 cams as it pushes my budget a bit, but am considering finding an m54b30 intake cam to trim and install, if I want to get into the head at all. I'll pull the valve cover and take a peak and if things look less than ideal I'll dive in. I'd love to be able to build this motor a bit more with s52 cams and vanos rebuild etc etc (maybe even stroking it to a 3.0l) but I'm pressed for time a bit.
The goal right now is to get the swap underway as quickly as possible (without avoiding obvious necessities) because I'll be taking classes that run from 10-2pm on saturdays while also working a full time job during the week. Busy busy!Leave a comment:
-
Im not 100% sure, but I believe that the M20 single mass is usable. Might need to change to a different TOB. I got mine lightened and balanced. Went from ~19# to ~12#. I had the same setup on my aluM52 car with the G260 and a sachs clutch. Felt awesome, OEM comfortLooking for single mass flywheel options, does anyone have any recommendations on steel single mass flywheels for an m52 with zf320? Dont want something as chattery and light as aluminum, but would prefer to not have a dual mass self adjusting clutch
also taking any and all recommendations for "while you're in there" items to replace or refresh since the engine will be out and on a stand for a bit before going into the e30Leave a comment:
-
Looking for single mass flywheel options, does anyone have any recommendations on steel single mass flywheels for an m52 with zf320? Dont want something as chattery and light as aluminum, but would prefer to not have a dual mass self adjusting clutch
also taking any and all recommendations for "while you're in there" items to replace or refresh since the engine will be out and on a stand for a bit before going into the e30Leave a comment:
-

Got a nice package from Jegs yesterday too!
Sent from my iPhone using TapatalkLeave a comment:
-
Daily'ed Sedan build: 1986 325
Went to work on the donor car today to try and get it running and driven up to where I will be doing the swap. Threw the new radiator in (old one had a leak) and used my e30 battery to try and start it up. Installed some new spark plugs for good measure and wasnt getting anything to fire. Pretty sure its a fueling issue, and pretty sure its gummed up injectors, but concerned because wouldnt it fire at last a few sparse times?
The car has sat for 6 months and not moved at all. I could hear the fuel pump making sounds and I double checked and was getting 11 volts at the connector. My fear is that there are some wires chewed up somewhere. I've found a few acorn storages and my coolant level wire is chewed into three pieces. Damn squirrels. Anyone have any other suggestions as to why the car wont fire? It recently got a new crank pos, sensor as well.
Leave a comment:
-
I look at that for sale thread quite often. I'll probably be cracking into the engine at some point this weekend so I maaaaayyyy be hitting you up for that vanos kit and possible chain tensioners/guides. But I wouldn't hold my breath as this is in pretty solid conditionDude, nice pick on the donor car! I had a 328 donor car but it had a grinding ZF so I sold it. Had I kept it, I probably would've followed through with my 24v swap.
I have new UUC underdrive pullies for your M52, e39 fuel rail (integrated FPR), new stage 1 dr vanos rebuild, Febi guides and tensioner set, and an achilles oil pan baffle, all of which you could probably use....
If you want to work something out, hit me up.Leave a comment:
-
Dude, nice pick on the donor car! I had a 328 donor car but it had a grinding ZF so I sold it. Had I kept it, I probably would've followed through with my 24v swap.
I have new UUC underdrive pullies for your M52, e39 fuel rail (integrated FPR), new stage 1 dr vanos rebuild, Febi guides and tensioner set, and an achilles oil pan baffle, all of which you could probably use....
If you want to work something out, hit me up.Leave a comment:
-
went down to work on the donor car today as the plan is to get it running enough to drive it up to the garage where I'll be doing the swap. From what I know, it needs a radiator and a battery, the seller included a brand new oem radiator that I think I'll be able to use for the swap, so thats great too. All I did was put oil in the cylinders and then helped my friend out with his e36 m3.
Hes putting an s54 oil pan and pump in as well as rebuilding the entire suspension and hard mounting the drivetrain. Should be very rigid. Its a pretty sweet track/canyon car with a buncha lightweight mods. I'll post more pics of it soon for sure.Leave a comment:

Leave a comment: