Announcement

Collapse
No announcement yet.

!!!!!Caution M20 porn inside!!!!!

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #16
    What mm are the throttle bodies?

    Comment


      #17
      34mm Bing throttles
      85 325e 2.7 ITB'd stroker

      Comment


        #18
        Originally posted by badvibrations View Post
        Ok this is hott and ghetto all at the same time. I'm demanding a write up:hitler: and a complete parts list after you got it all installed and functional.
        x2 por favor?

        These are sweet...8)
        If life passes you by... Downshift.

        Comment


          #19
          Sorry guys no write up is in the works, there is way too much custom fabed stuff. Heck this is the 3-rd time now I've tried to make a set and this is the best one so far.
          Last edited by rs4pro3; 04-20-2008, 08:26 PM.
          85 325e 2.7 ITB'd stroker

          Comment


            #20
            Thats awesome.What will you make the plentum out of? I assume your oe fuel rail will be used, correct?
            Supatek -noun - your basic know it all

            Comment


              #21
              I've got a bunch of ABS plastic I'm going to make the plenum out of. And ya I'm just going to use the stock fuel rail. I'll have to make some small brackets to hold it in place but no biggy.
              85 325e 2.7 ITB'd stroker

              Comment


                #22
                Made a vacuum manifold to bring the vacuum from each runner to a single point to run to the MAP sensor in the megasquirt ECU

                85 325e 2.7 ITB'd stroker

                Comment


                  #23
                  I like.
                  sigpic

                  Comment


                    #24
                    thats pretty bad ass. might i ask where you got the manifold adapters? i have no problem fabbing stuff at all :)

                    pm me if you would like.

                    Comment


                      #25
                      I think i am going to go out on a limb here and say that Ely most likely made those adapters using a stock intake as a donor.

                      With a real budget and access to serious tools, dude could be scary.

                      Color me impressed.
                      Current Cars
                      2014 M235i
                      2009 R56 Cooper S
                      1998 M3
                      1997 M3

                      Comment


                        #26
                        manifold adapters? I just cut up a stock intake manifold and machined the runners to be round on the outside.
                        Thanks Dave, Ya everything I've been doing has just been with a drill, drill press, grinder, and sawzall. If i had a Mill and lathe in the garage i'd be making some crazy chit. I should of gotten around to making some stuff at my old job, but I was too busy working, and making parts for the machine we were building.
                        Last edited by rs4pro3; 04-23-2008, 05:56 PM.
                        85 325e 2.7 ITB'd stroker

                        Comment


                          #27
                          Looks awesome, i can't wait to see the finished product!

                          Comment


                            #28
                            I may have it on the car very soon, at first I'm going to just run it NA, while I get the throttles all synced up and the kinks etc.. worked out and get it ruffly re tuned. Then dump back on the supercharger and up the boost. I have everything made to where I could stick in on NA, and just put filters on each runner
                            85 325e 2.7 ITB'd stroker

                            Comment


                              #29
                              why not drop map and shoot for alpha?
                              that setup looks like it could pose problems

                              Comment


                                #30
                                Originally posted by rs4pro3 View Post
                                manifold adapters? I just cut up a stock intake manifold and machined the runners to be round on the outside.
                                Thanks Dave, Ya everything I've been doing has just been with a drill, drill press, grinder, and sawzall. If i had a Mill and lathe in the garage i'd be making some crazy chit. I should of gotten around to making some stuff at my old job, but I was too busy working, and making parts for the machine we were building.
                                really? well now i feel stupid. haha. would you mind if i duplicated your design?

                                Comment

                                Working...
                                X