My m50 is pinging. Running out of ideas.

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • digger
    replied
    its not clear if this pinging is a part throttle or WOT reading the first post.

    Leave a comment:


  • Wishno87
    replied
    Ordered a fuel pressure tester yesterday. My car has 260k on the body so it's possible my fuel pumps are not in the best condition. My car is a 87 325i so it has the dual pumps.

    Leave a comment:


  • Ryann
    replied
    These cars are not chipped. I can't speak for Wishno but the Modis shows my mixture is stoich when the pinging is occurring. Also, I get no lean codes, or any codes for that matter.

    Leave a comment:


  • ForcedFirebird
    replied
    Originally posted by 328ijunkie
    Throw a set of 19lb injectors in there. Obviously not the "best" choice but will add 15% more fuel or so (not doing the math) across the board and shut it up most likely. I see a lot of m50s ping on aftermarket chips at <full throttle as the timing map iirc is across the board while the fuel maps that are commonly modded are WOT only (don't quote me on that)
    He said it's a stock chip. And actually a lot of the chips I have read personally, don't have much done at all in part throttle.

    Leave a comment:


  • 328ijunkie
    replied
    Throw a set of 19lb injectors in there. Obviously not the "best" choice but will add 15% more fuel or so (not doing the math) across the board and shut it up most likely. I see a lot of m50s ping on aftermarket chips at <full throttle as the timing map iirc is across the board while the fuel maps that are commonly modded are WOT only (don't quote me on that)

    Leave a comment:


  • meanEG
    replied
    Originally posted by Ryann
    ^Change your oil afterward Josh.

    Found a thread where a guy unplugged his IAT sensor and it 'went away'. Unplugged mine before leaving work, did not go away and gave me a CEL. Watching and listening closely there is moderate to severe pinging depending on the load, only when near or up to operating temp and only between 1500-2900 rpm.
    You could be running extremely Lean. Lean can knock as well. I dont think that's what the issue is, but you need to look at the plugs to make sure. You don't want to melt a plug if piston. Clean the carbon and all will be good I bet.

    Leave a comment:


  • Dj Buttchug
    replied
    Originally posted by ForcedFirebird
    Are you sure it's not vanos rattle starting?
    this is what I was thinking right when I started noticing the sound... Its difficult to differentiate mine as it doesnt seem to appear as bad as others described.

    Leave a comment:


  • ForcedFirebird
    replied
    Are you sure it's not vanos rattle starting?

    Leave a comment:


  • Ryann
    replied
    ^Change your oil afterward Josh.

    Found a thread where a guy unplugged his IAT sensor and it 'went away'. Unplugged mine before leaving work, did not go away and gave me a CEL. Watching and listening closely there is moderate to severe pinging depending on the load, only when near or up to operating temp and only between 1500-2900 rpm.

    Leave a comment:


  • Wishno87
    replied
    Originally posted by Dj Buttchug
    been watching this thread. My m50 has similar issues as well. Was running 89 and it would ping at freeway speed on accel. Upped to 91 and it went away... Not sure if its just my mind or not but I swear I can hear it still.
    Haha this is how i feel too! I will be driving other cars and i will feel like I'm hearing pinging until I really intently listen :loco:

    Leave a comment:


  • Dj Buttchug
    replied
    been watching this thread. My m50 has similar issues as well. Was running 89 and it would ping at freeway speed on accel. Upped to 91 and it went away... Not sure if its just my mind or not but I swear I can hear it still.

    Leave a comment:


  • digger
    replied
    Originally posted by Wishno87
    Ya but i want to run it though the intake and not the crank case. I was just wondering if it would seep past the pistons and into the oil. Probably not an issue but I tend to be overly cautious.
    a little might but not enough to worry about methinks.

    yes putting it through the vacuum hose or similar is the go

    Leave a comment:


  • Wishno87
    replied
    Originally posted by digger
    doesnt it say you can put seafoam in the oil?personally i would change the oil but thats only an opinion
    Ya but i want to run it though the intake and not the crank case. I was just wondering if it would seep past the pistons and into the oil. Probably not an issue but I tend to be overly cautious.

    Leave a comment:


  • digger
    replied
    Originally posted by Wishno87
    I was just about to do it today but I wanted to ask you guys first if I should worry about it getting into the oil at all. From what I understand once you have the intake siphon up the seafoam you are supposed to let it sit for 10 min before starting it again and beginning the smoke show.

    Im assuming the "waiting 10 min" is for the seafoam to soak in but I don't want it to seep into the oil because I just changed it a few days ago.
    doesnt it say you can put seafoam in the oil?personally i would change the oil but thats only an opinion

    Leave a comment:


  • Wishno87
    replied
    Originally posted by Ryann
    In for results on Seafoam.
    I was just about to do it today but I wanted to ask you guys first if I should worry about it getting into the oil at all. From what I understand once you have the intake siphon up the seafoam you are supposed to let it sit for 10 min before starting it again and beginning the smoke show.

    Im assuming the "waiting 10 min" is for the seafoam to soak in but I don't want it to seep into the oil because I just changed it a few days ago.

    Leave a comment:

Working...