E36 flywheels

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • e30s52
    R3V Elite
    • Oct 2007
    • 5235

    #16
    /\ what hp rating are they good till?

    www.gutenparts.com
    One stop shopping for NEW, USED and EURO PARTS!

    Comment

    • m3boost
      Advanced Member
      • Oct 2005
      • 110

      #17
      Originally posted by DaN
      I have this 16lb single mass flywheel, purchased on ebay. It fits perfect, and its about 9lbs lighter than the dual mass. Its a good comprimise between stock, and alum race flywheels.


      http://cgi.ebay.com/ebaymotors/F1-RA...mZ400002009049

      I have this flywheel still in box and I'll let it go for 150.00. I bought the whole kit but decided to stay with the stock flywheel cause was going turbo..
      88 e30/s50 gt35r turbo m3



      96 gt4094r turbo m3
      452 rwhp, 455 rwtq at 14 psi 91 octane
      681 rwhp, 684 rwtq at 25 psi E65

      Comment

      • Jean
        Moderator
        • Aug 2006
        • 18228

        #18
        PM sent
        Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205



        OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827

        Comment

        • Jean
          Moderator
          • Aug 2006
          • 18228

          #19
          Originally posted by DaN
          No problems with the install, fits with no issue of course only with the intended application. S50/zf.
          You will get some trans rattle. My zf uses atf. I just swapped to redline MT90 and the noise is gone.
          Cool. I have a ZF as well, and it came with ATF sticker on it. I take it this flywheel should work just fine with m52 as well or I wonder if it's somehow specific to s50 only?
          Mtech1 v8 build thread - https://www.r3vlimited.com/board/sho...d.php?t=413205



          OEM v8 manual chip or dme - https://www.r3vlimited.com/board/sho....php?p=4938827

          Comment

          • MR 325
            Moderator
            • Oct 2003
            • 37824

            #20
            Originally posted by e30s52
            /\ what hp rating are they good till?
            It's a stock replacement.
            BimmerHeads
            Classic BMW Specialists
            Santa Clarita, CA

            www.BimmerHeads.com

            Comment

            • evil_twin
              R3VLimited
              • Nov 2007
              • 2965

              #21
              Originally posted by DaN
              I have this 16lb single mass flywheel, purchased on ebay. It fits perfect, and its about 9lbs lighter than the dual mass. Its a good comprimise between stock, and alum race flywheels.


              http://cgi.ebay.com/ebaymotors/F1-RA...mZ400002009049
              I have this flywheel with their 6puck clutch and pressure plate set up. I love it! My friend has it in his e36 m3 and loves it also. When you have this set up, BE SURE to install the clutch disc correctly. This is installed 'opposite' of how the OE clutch came out.
              I got a fender roller now! LMK if you need me to roll your fenders or want to rent the tool from me locally.

              Paypal: vdang5@gmail.com

              Delta Auto Care
              2875-C Towerview Road
              Herndon, VA
              703.435.1375

              My Feedback Thread: Evil_Twin

              Comment

              • DaN
                E30 Fanatic
                • Dec 2003
                • 1265

                #22
                Are you sure? The clutch disc is made with a flywheel side, and trans side. And are usually labeled. I didnt install anything different than stock. And usually if you do, the results are not desirable.

                Comment

                • evil_twin
                  R3VLimited
                  • Nov 2007
                  • 2965

                  #23
                  Well, since its a lighter weight flywheel and a single instead of a dual mass, thats how they have you install it. If I remember correctly when we installed it on the M3, we had it incorrect, and it was a B!TCH to remove the transmission after that. And that was installed with the hat of the disc facing the pressure plate. If you research on bimmerforums there have been numerous people doing the same thing we did, and some of them actually bent their input shaft removing the transmission.

                  But I installed it correct, and I love the set up on my m52/zf e30.
                  I got a fender roller now! LMK if you need me to roll your fenders or want to rent the tool from me locally.

                  Paypal: vdang5@gmail.com

                  Delta Auto Care
                  2875-C Towerview Road
                  Herndon, VA
                  703.435.1375

                  My Feedback Thread: Evil_Twin

                  Comment

                  • e30polak
                    R3V OG
                    • Nov 2006
                    • 6136

                    #24
                    I got the Fidanza Flywheels from Gripforce, with a sachs heavy duty clutch kit. The flywheel is 13lbs, and only a little over $100 then the 16lb F1 Racing Flywheel. Works great, but I do get some chatter letting off in 4th and 5th.

                    Check out Undr8d Empire on Facebook: www.facebook.com/Undr8dEmpireLlc

                    INSTAGRAM: @UNDR8D_EMPIRE

                    Scarlet V2 - #Project333Ti by @castromotorsport, @kingsautobodyshop, @bimmerheads, @hardmotorsport, @excel_motorsports & @mateomotorsports - http://www.r3vlimited.com/board/showthread.php?t=371356

                    Your signature picture has been removed since it contained the Photobucket "upgrade your account" image.

                    Comment

                    • dpgrand
                      Advanced Member
                      • Sep 2008
                      • 179

                      #25
                      Is anyone running the UUC lightweight flywheel? They make a stage 1 and a stage 2.

                      Comment

                      • golde30
                        R3V OG
                        • Nov 2003
                        • 11464

                        #26
                        Originally posted by DaN
                        I have this 16lb single mass flywheel, purchased on ebay. It fits perfect, and its about 9lbs lighter than the dual mass. Its a good comprimise between stock, and alum race flywheels.


                        http://cgi.ebay.com/ebaymotors/F1-RA...mZ400002009049
                        i think this is the same one i am running on my s50 swap. i have this flywheel, with oe sachs clutch kit for s50, and running the s50 starter. i am using my stock getrag260 though. my clutch setup feels really good, no problems at all so far.
                        IG: @Baye30

                        FRONT VALENCE IS ZENDER!!! STOP FILLING MY PM BOX PPL!!!

                        Comment

                        • hugh jass
                          R3VLimited
                          • Dec 2003
                          • 2220

                          #27
                          Originally posted by dpgrand
                          Is anyone running the UUC lightweight flywheel? They make a stage 1 and a stage 2.
                          i've got the uuc stage 1 flywheel and e34 m5 clutch on my obd1 s52. its awesome. engine spins up really nicely.
                          ______________________
                          ex-Chief Operating Officer
                          Blunt Tech Industries
                          West Coast and Pacific Rim

                          Comment

                          • dpgrand
                            Advanced Member
                            • Sep 2008
                            • 179

                            #28
                            Originally posted by hugh jass
                            i've got the uuc stage 1 flywheel and e34 m5 clutch on my obd1 s52. its awesome. engine spins up really nicely.
                            Awesome. This is the setup that I have been eying.

                            Comment

                            Working...