Announcement

Collapse
No announcement yet.

iX wheel thread

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Originally posted by nando View Post
    spacers make the offset lower, so no, you don't need spacers. ET25 is already a bit on the low side, but they should fit just fine with stock suspension and 205/55 tires.

    Oh thanks for clearing that up. It would be pretty tight with the hr and bilstein setup then
    1988 325iX - sold but not forgotten
    1984 MTech1 323i

    Comment


      yeah it would rub over dips/bumps and with people in the back, not terribly but it could be annoying after a while. you could trim the rear flares and roll the fenders and it would fit fine.
      Build thread

      Bimmerlabs

      Comment


        Yeah that's what I figured.

        Like a good neighbor nando is there!
        1988 325iX - sold but not forgotten
        1984 MTech1 323i

        Comment


          Originally posted by nando View Post
          no, ET28 is too low for an 8" wheel/225 tire. you could maybe run a 205, but I'm thinking that would probably rub in the back anyway.

          Thanks Nando, 16x7 all around it is, then !

          Comment


            15x8 ET25 73.1CB stock suspension, How tight would they be and would spacers help?

            Comment


              Too low for an 8. No, spacers push the wheels out more.
              Build thread

              Bimmerlabs

              Comment


                15x8 +36
                205/55 Direzza

                1990 Brilliantrot 325iS Build Thread
                1989 Zinnoberrot M3 Build Thread

                Comment


                  what rims are those bob?
                  1988 325iX - sold but not forgotten
                  1984 MTech1 323i

                  Comment


                    Originally posted by 6A LDY View Post
                    what rims are those bob?
                    Dem be 949 Racing 6ULs.
                    1990 Brilliantrot 325iS Build Thread
                    1989 Zinnoberrot M3 Build Thread

                    Comment


                      Originally posted by AWDBOB View Post
                      Dem be 949 Racing 6ULs.

                      You da man
                      1988 325iX - sold but not forgotten
                      1984 MTech1 323i

                      Comment


                        Hows the strut clearance? I'm pretty sure with a 3mm spacer up front, you could fit 225s all around
                        Build thread

                        Bimmerlabs

                        Comment


                          Lets put this here also. Not my car, just see it in fb.



                          Rims are 16×8 et 18, tyres are 205/55/r16 toyo NA20..all season
                          There is some lower spring also, but i dont know how much
                          https://www.facebook.com/Cry_77_IX-110483784967661
                          https://www.instagram.com/cry_77_ix/

                          Comment


                            Originally posted by nando View Post
                            Hows the strut clearance? I'm pretty sure with a 3mm spacer up front, you could fit 225s all around
                            Strut clearance is about 3mm (inner lip to strut). I definitely think you're right. It doesn't rub at all, which is nice, but there is definitely a hair of stretch with the 205s on the 8" wheel.

                            I wanted to run a 225 but the RS3s were back ordered again and I couldn't swing R888s just yet. Next time!
                            1990 Brilliantrot 325iS Build Thread
                            1989 Zinnoberrot M3 Build Thread

                            Comment


                              Originally posted by Sade View Post
                              Lets put this here also. Not my car, just see it in fb.



                              Rims are 16×8 et 18, tyres are 205/55/r16 toyo NA20..all season
                              There is some lower spring also, but i dont know how much
                              that looks awful. those wheels stick out at least an inch past the fenders.
                              Build thread

                              Bimmerlabs

                              Comment


                                :D :D I liked :)
                                https://www.facebook.com/Cry_77_IX-110483784967661
                                https://www.instagram.com/cry_77_ix/

                                Comment

                                Working...
                                X