ESPECIALLY if I've posted it.
Sorry, I missed that it was a 3l engine. In which case, it's very much a wash.
40's are at the top end of their flow, and will be a limit if you REALLY hold it wide open after 6500,
whereas the 45s might be a bit harder to tune just off idle.
Yes, the progression drillings come into play based solely on throttle angle, which will have to be smaller with the 45's at low sppeds.
If there was a non- destructive way to modify them, it'd be a lot easier to tune street cars. I've only really thoroughly
worked on them with an M10 race car, so I'm only an expert on digger's internet.
As to boosters, not much help as the E30 race car has a stock- type setup per the rules,
and I've left the stock booster.
On the M10 race car, I eliminated the booster, but it makes for a pretty hard push for a cold- pad stop,
and that's also true on the other non- boosted disc- brake cars I have some experience with
(volvo 122, datsun roadster). So no help here. the ibooster looks cool- but if it wants car data,
that's a bunch of work.
t
Well, I Am Going To Add Triple Webers To My 3.0L M20…
Collapse
X
-
Fair play! I am pretty much secure on the DCOE’s.
The next thing I can’t get past is the brake booster. An iBooster seems like a logical choice, but I am concerned that the feel wont be as familiar as ‘normal’ cars do. I wont be able to run the Canbus from what I can sort out, so it will be in a sort of emergency mode with basic hookups. I am not sure how modulated this will feel. I daily drive a 2025 vehicle and it feels like I would hope my E30 would feel. I am just not confident I can expect the same.
Any input on what boosters have worked for others running DCOE’s would be super appreciated. I suspect I can pull enough vacuum off an evenly pulled manifold to support a booster.
—————-
In other news, I got a line on some Racing Dynamics headers custom made by a guy in Ontario. I am going to pull the trigger. Would anyone else like a set? They aren’t ‘cheap’ but seemingly very well made and a once-in-a-life-time header. (At least that’s what I tell my wife)
Leave a comment:
-
dont trust anything you read on forums
Thank you Toby and Digger for the input!
So my actual CC's are 2926. So 488cc per cylinder. If I am gathering this correctly, you are saying with the 40's, the progression holes will be uncovered and thus assist better than if I run 45's and a 34mm choke? (which is at its min)
I feel inclined to give the FJAS a try based on the reports coming back to me. Its just a bit unusual for me to order 'replica' parts, but smoother tuning is key, and it sounds the FJAS have more consistency. But man, its hard to say. So many differing opinions in this subject. I wasn't expecting this! Haha
Which booster did you use on your race car? Was your setup in an E30? Also, did you run vacuum from the carbs or the manifold?Leave a comment:
-
Thank you Toby and Digger for the input!
Yes, anecdotally it makes sense, as a 36mm choke only provides a 4mm restriction on the 40mm bore.
In THEORY that's not very much 'depression' for metering.
I really do think that 40's with a 34mm choke will be enough if you're not planning on holding the throttle
open for minutes at 7000+ rpm. But then, 45's ARE bigger...
I had expected the race car to change character when I put 36mm chokes in, but it really didn't seem to affect
anything very much, other than top end airflow. Metering did change, but it wasn't more than incremental.
Keeping in mind, of course, that while a race car spends very little time at 'puttering' speeds, I didn't notice
anything unusual in driving out to pregrid...
A 36mm choke in a 45 would provide a very good venturi, and give good metering. Again, the real challenge
will be the tiny throttle angles it'll need to putter down to pregrid at 35mph, and it won' uncover the progression
holes very much, if at all...
yup, an M10b20 has a 500ml cylinder, and an M20b25 has a 416ml cylinder, so each throat on an M20 will be
drawing 83% of what an M10 will at the same rpm...
If FJAS is one of the suppliers from China, I've heard similar- that some Cast in China carbs are very good for what they are.
If you can get a return guarantee, it would probably be worth trying them. When I was having issues,
I put pyrometers in the headers, and for $50 a runner, they were really useful, in combination with a wideband
in the collector, at telling me how close to balanced the carbs were.
When I had a booster on the racecar, with a pretty aggressive cam, I never had vacuum issues.
Closed throttle is closed throttle, and the booster just needs to be evacuated between braking events.
That said, getting rid of the booster is nice, since it's always in the way.
t
So my actual CC's are 2926. So 488cc per cylinder. If I am gathering this correctly, you are saying with the 40's, the progression holes will be uncovered and thus assist better than if I run 45's and a 34mm choke? (which is at its min)
I feel inclined to give the FJAS a try based on the reports coming back to me. Its just a bit unusual for me to order 'replica' parts, but smoother tuning is key, and it sounds the FJAS have more consistency. But man, its hard to say. So many differing opinions in this subject. I wasn't expecting this! Haha
Which booster did you use on your race car? Was your setup in an E30? Also, did you run vacuum from the carbs or the manifold?
Leave a comment:
-
Yes, anecdotally it makes sense, as a 36mm choke only provides a 4mm restriction on the 40mm bore.It seems running 40mm carbs but having 36mm chokes can cause some drivability issues
In THEORY that's not very much 'depression' for metering.
I really do think that 40's with a 34mm choke will be enough if you're not planning on holding the throttle
open for minutes at 7000+ rpm. But then, 45's ARE bigger...
I had expected the race car to change character when I put 36mm chokes in, but it really didn't seem to affect
anything very much, other than top end airflow. Metering did change, but it wasn't more than incremental.
Keeping in mind, of course, that while a race car spends very little time at 'puttering' speeds, I didn't notice
anything unusual in driving out to pregrid...
A 36mm choke in a 45 would provide a very good venturi, and give good metering. Again, the real challenge
will be the tiny throttle angles it'll need to putter down to pregrid at 35mph, and it won' uncover the progression
holes very much, if at all...
yup, an M10b20 has a 500ml cylinder, and an M20b25 has a 416ml cylinder, so each throat on an M20 will be
drawing 83% of what an M10 will at the same rpm...
If FJAS is one of the suppliers from China, I've heard similar- that some Cast in China carbs are very good for what they are.
If you can get a return guarantee, it would probably be worth trying them. When I was having issues,
I put pyrometers in the headers, and for $50 a runner, they were really useful, in combination with a wideband
in the collector, at telling me how close to balanced the carbs were.
When I had a booster on the racecar, with a pretty aggressive cam, I never had vacuum issues.
Closed throttle is closed throttle, and the booster just needs to be evacuated between braking events.
That said, getting rid of the booster is nice, since it's always in the way.
t
Leave a comment:
-
Thank you for the time spent explaining these details. I have a few specific questions.You'll be able to make either 40's or 45s work, and the difference will be mostly in mixture control.
It might not even be all that hard to get either to work in similar circumstances.
However, this has been my experience:
I bought a 2L race car that had 40s with 32mm chokes per the rules of the class.
It ran fine, made 150 solid horsepowers, and pulled to a 7000 redline, falling off starting about 6700.
Long runner Canon manifolds.
The rules changed. Now 45s were ok, and chokes were unrestricted.
I went to a 34mm choke, and then a 36mm choke, and the redline went to 7500 with absolutely no falloff.
Idle SHOULD have gone to shit with 36, but the car metered well from 2000, and pulled strongly
(as in, solid a/f ratios) from there. Horsepowers were never measured, but lap times said they went up significantly.
Doing the straight maths, probably to 180.
I then got me some Spanish 45's, and lap times went to hell. After some EGT gauges, it turned out that one
jet well of one Weber was machined too deep, and there was no real fix for it.
Then I got me another Weber, and stuck 36mm chokes in, and after some more tuning, got back to my
40 lap times. Went to 38 mm chokes. Didn't go noticeably faster, and tuning wasn't any more difficult.
The jet combinations made more SENSE than they did on the 40s (larger mains, smaller air correctors)
but the lap times stayed roughly the same. This was on the same type Canon manifold, but opened
up for 45s. All the other variables factored in, the 45's weren't good for more than tenths of a second
on the straights. Which in a race car is all well and good, but on a street car, silly.
So here's my limited opinion: with a smaller cylinder M20, I'd stick with 40s on the street. Then the throttle
plate will open further at just-off-idle, and the progressions will have a chance to work. If you start
on a 34mm choke, tuning will be easy, and your carburetted top end will probably be over 7000, based on what
I experienced with the 2l engine. You WILL be giving up just a titch- but unless you're planning on
tuning at Bonneville and running tracks with long straights, you're REALLY not going to notice all that much.
What you get in return is better mixture control at idle.
Is it a big deal?
Prolly not. So if 45's make you happier, do that.
As to progression drillings, I've always been frustrated by the Weber method. If I was to spend real time
on street development, that's where I'd start filling and drilling....
For spark, it's not going to matter. I used a 6MSDal for the limiter with a rusty Accel coil
and never had any blowout problems.
If you already have the 'squirts, I'd use it for its tunability. There's both power and driveability in a good,
load- sensing spark timing system.
I found DBilas' opinions to be... opinions. And their products to be... heavy. They certainly go fast, though.
t
opinions are like Miatas...
It seems running 40mm carbs but having 36mm chokes can cause some drivability issues around town. At least I have been told this. I get the impression 30mm-34mm is ideal for 40's but bigger than that 45's make more sense. Do you think doing an initial setup with a 36mm choke/45mm would make my 3.0L hard to tune?
Are you referring to a stock m20 as a 'smaller cylinder M20?'
My local weber supplier (redline) says that the FJAS carbs are better quality than the Spanish Webers. They are also half the price. Thats quite an impressive claim. Especially when the Weber forms I have recently signed on seem to say the same thing. Anyone here have anything to add about the FJAS carbs?
I am looking pretty seriously into the iBooster setup. I am doing some deeper dives with this, but it seems like a better compromise considering the vacuum isn't the best with carbs, and it allows even more space. My daily has an iBooster setup and it works quite well. Any thoughts on this conversion for my touring? It would be nice to setup the canbus, but I feel a bit out of my comfort zone sorting the electronics out. (perhaps I am over-thinking the difficulty)
Thank you all again for your help!
Leave a comment:
-
You'll be able to make either 40's or 45s work, and the difference will be mostly in mixture control.
It might not even be all that hard to get either to work in similar circumstances.
However, this has been my experience:
I bought a 2L race car that had 40s with 32mm chokes per the rules of the class.
It ran fine, made 150 solid horsepowers, and pulled to a 7000 redline, falling off starting about 6700.
Long runner Canon manifolds.
The rules changed. Now 45s were ok, and chokes were unrestricted.
I went to a 34mm choke, and then a 36mm choke, and the redline went to 7500 with absolutely no falloff.
Idle SHOULD have gone to shit with 36, but the car metered well from 2000, and pulled strongly
(as in, solid a/f ratios) from there. Horsepowers were never measured, but lap times said they went up significantly.
Doing the straight maths, probably to 180.
I then got me some Spanish 45's, and lap times went to hell. After some EGT gauges, it turned out that one
jet well of one Weber was machined too deep, and there was no real fix for it.
Then I got me another Weber, and stuck 36mm chokes in, and after some more tuning, got back to my
40 lap times. Went to 38 mm chokes. Didn't go noticeably faster, and tuning wasn't any more difficult.
The jet combinations made more SENSE than they did on the 40s (larger mains, smaller air correctors)
but the lap times stayed roughly the same. This was on the same type Canon manifold, but opened
up for 45s. All the other variables factored in, the 45's weren't good for more than tenths of a second
on the straights. Which in a race car is all well and good, but on a street car, silly.
So here's my limited opinion: with a smaller cylinder M20, I'd stick with 40s on the street. Then the throttle
plate will open further at just-off-idle, and the progressions will have a chance to work. If you start
on a 34mm choke, tuning will be easy, and your carburetted top end will probably be over 7000, based on what
I experienced with the 2l engine. You WILL be giving up just a titch- but unless you're planning on
tuning at Bonneville and running tracks with long straights, you're REALLY not going to notice all that much.
What you get in return is better mixture control at idle.
Is it a big deal?
Prolly not. So if 45's make you happier, do that.
As to progression drillings, I've always been frustrated by the Weber method. If I was to spend real time
on street development, that's where I'd start filling and drilling....
For spark, it's not going to matter. I used a 6MSDal for the limiter with a rusty Accel coil
and never had any blowout problems.
If you already have the 'squirts, I'd use it for its tunability. There's both power and driveability in a good,
load- sensing spark timing system.
I found DBilas' opinions to be... opinions. And their products to be... heavy. They certainly go fast, though.
t
opinions are like Miatas...
Leave a comment:
-
Sorry, i cant provide any informed comments about progression holesThank you for the details Digger. I have reached out to Rama, and they do not have anything to do with carbs any longer. I am about to pull the trigger on some 45's Webers. My options are between a 5 progression hole vs 3. The cost is about $1000 more for the 5-hole. The seller/tuner (based in England) says the 3-hole setup would be fine since I have a SOHC. I can understand how a 5-hole would work more smoothly, but it would require more tuning etc. I dont mind spending more, but only if it makes sense. Any advice between the two?
Does anyone know is Andrew (SkiFree) is still around? He seems to have all the answers I may need, but he hasnt been active on any of his accounts in 5-years. I recall him being a regular on this form in the past.
try contacting Adams Autosport https://www.instagram.com/adamsautosport/?hl=en if you haven't already. Someone else might have other contactsLeave a comment:
-
Thank you for the details Digger. I have reached out to Rama, and they do not have anything to do with carbs any longer. I am about to pull the trigger on some 45's Webers. My options are between a 5 progression hole vs 3. The cost is about $1000 more for the 5-hole. The seller/tuner (based in England) says the 3-hole setup would be fine since I have a SOHC. I can understand how a 5-hole would work more smoothly, but it would require more tuning etc. I dont mind spending more, but only if it makes sense. Any advice between the two?
Does anyone know is Andrew (SkiFree) is still around? He seems to have all the answers I may need, but he hasnt been active on any of his accounts in 5-years. I recall him being a regular on this form in the past.Leave a comment:
-
The bigger mid range torque loss will come from the excessively short runners, not excess diameter (though neither are ideal). You can choose a suitable choke and increase runner length if space allows to mitigate a bit of excess diameter and similarly if the runners are short you can somewhat kind of make up for it with small diameter runners but this doesn't mitigate as well as the other situation. So you need to look at the big picture how long of a runner can you fit as that may dictate which size is best.
Thank you for this Digger! My intention is to make power as the main objective. My only scare was to loose all low end grunt to accomplish this. After getting sucked into watching videos last night about this, (thanks to digger) I feel more at ease with the 45mm option.
Local to me there are some used Spanish Webers available. Outside of the jetting needing to be sorted for my specific motor (which can be expensive) I am weary of buying used to save $1000. If I bought used carbs, my plan would get an ultrasonic cleaner to make things new again. I am not sure if the Spanish Webers are of a higher quality now than before but my hope is they are. Any input on buying used vs new? I can only get one-Italian DCOE Weber from a friend, matched with 2 x Spanish Webers if I go used.
I plan to order all my equipment next week. Can anyone lay an option on the Dbilas manifold vs Webco? Dbilas looks pretty simple for the bitch tube, where as the CNC'd plate looks like it will be fairly custom. Outside of that they both seem to be at or near 0-degrees to the head which seems to be the best way.
Thank you all for spending the time helping me out!
- Jan
the dbilas fits like the stock setup as far as breather tube goes but it may or may not not be the optimum angle off the head for what you are doing, and more than likely you're going to need to have really short runners to clear booster. you can see how it will fit by comparing to their ITB setup and how their airbox runner has a massive bend in it to clear booster.
The internal ports on dbilas manifold are not the best if you're trying for a maximum effort kind of thing as they really need the roof to be welded and ported as there is a big bulge in the way (i had this done before the RHD setup existed) but still function fine for most applications out of the box.
i would have a chat to Rama at RHD he used to run webers before developing the RHD kit and he will be able to give you some optionsLeave a comment:
-
I am also needing some advice on my ignition setup. I may be eliminating megasquirt as the harness is going to be rebuilt for the carb setup. Although running the TPS on the carbs would be a benifit MS can supply. I run wasted spark, but many have advised me to go back to the stock setup as apparently wasted spark burns out spark plugs. Would a MSD ignition be the best option or should I do a NoDiz, etc? I am open to all suggestions. I just need an easy setup for ignition tuning.Leave a comment:
-
Thank you for this Digger! My intention is to make power as the main objective. My only scare was to loose all low end grunt to accomplish this. After getting sucked into watching videos last night about this, (thanks to digger) I feel more at ease with the 45mm option.
It is not clear whether you are concerned about making power or justing have it running right.
this guy has tested various setups if you look for one below. This is not an m20 but doesnt matter as the power level are same per cyl
There are other videos
https://www.youtube.com/@PenguinMotors/videos
Local to me there are some used Spanish Webers available. Outside of the jetting needing to be sorted for my specific motor (which can be expensive) I am weary of buying used to save $1000. If I bought used carbs, my plan would get an ultrasonic cleaner to make things new again. I am not sure if the Spanish Webers are of a higher quality now than before but my hope is they are. Any input on buying used vs new? I can only get one-Italian DCOE Weber from a friend, matched with 2 x Spanish Webers if I go used.
I plan to order all my equipment next week. Can anyone lay an option on the Dbilas manifold vs Webco? Dbilas looks pretty simple for the bitch tube, where as the CNC'd plate looks like it will be fairly custom. Outside of that they both seem to be at or near 0-degrees to the head which seems to be the best way.
Thank you all for spending the time helping me out!
- JanLeave a comment:
-
It is not clear whether you are concerned about making power or justing have it running right.
Thank you for your input Toby. Dbilas insists I get 45mm Webers for my motor as they feel it will fall pretty flat on the top end. From your experience, would you say this is true? Street drivability is key, but I do love 7,000 RPM. I know you cant get both to perform perfectly, but I am literally getting split opinions on which size to move forward with. Hence my question to people who have real world experience with M20's.
this guy has tested various setups if you look for one below. This is not an m20 but doesnt matter as the power level are same per cyl
There are other videos
Leave a comment:
-
No idea on the M20 manifold situation these days- triple Webers are fantastic, but not currently in vogue.
All I can add is that for a street- driven engine under 3 liters, 40's will probably be easier to tune at low loads.
You'll have less throttle plate area, and with a relatively small venturi, better idle and transition metering.
The throttle linkage is important- you can certainly do it yourself, but look up Hal's design on www.2002faq.com
for ideas on how to do it well.
DCOEs are their own beast.
t
Thank you for your input Toby. Dbilas insists I get 45mm Webers for my motor as they feel it will fall pretty flat on the top end. From your experience, would you say this is true? Street drivability is key, but I do love 7,000 RPM. I know you cant get both to perform perfectly, but I am literally getting split opinions on which size to move forward with. Hence my question to people who have real world experience with M20's.Leave a comment:

Leave a comment: