Well, I Am Going To Add Triple Webers To My 3.0L M20…

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • digger
    replied
    Originally posted by E30-TourZing

    I thought so, and I was careful putting it back together, but AI says it’s not symmetrical - and I don’t have another one kicking around to see.

    when I have installed them in the past, the push rod would touch and leave about 1cm of space before the flange hit. This time that didn’t happen.
    i have one somewhere for a g260 i will see if i can find it later today. I am going by looking at pics on FCP/ECS atm for a new one not an original

    Leave a comment:


  • E30-TourZing
    replied
    Originally posted by digger
    isn't the clutch fork symmetrical end to end?
    I thought so, and I was careful putting it back together, but AI says it’s not symmetrical - and I don’t have another one kicking around to see.

    when I have installed them in the past, the push rod would touch and leave about 1cm of space before the flange hit. This time that didn’t happen.

    Leave a comment:


  • digger
    replied
    isn't the clutch fork symmetrical end to end?

    Leave a comment:


  • E30-TourZing
    replied
    Here are some update photos
    Attached Files

    Leave a comment:


  • E30-TourZing
    replied
    Here is an update on where I am at. Basically I have the car about as far as I am going to take it. Next step, my tuner is going to build me a harness off of the NoDiz ME100X ignition. Then do startup and rolling road to set everything up.

    This will be the last bigger build I do for a long while. Working 60+ hours a week with my job and spending my evenings and weekends slaving away has lead to this build not being as much fun as it should be. I also seem to have made a pretty annoying mistake. When I removed my slave cylinder before I pulled the motor, the rod was held in the bell housing and had pushed itself out of the slave cylinder. It felt normal, so I didnt do anything to look deeper. Upon reinstalling slave I may have installed the fork the wrong way. Would it make sense that the slave push rod doesn't have enough length if its pushing on the side where the pin is supposed to be? I am running a RHD lightweight flywheel and stock Sachs clutch kit.

    I am fearful I now need to remove the transmission to confirm its correct. Any suggestions on what might be the issue?

    Leave a comment:


  • Panici
    replied
    That absolutely looks the business.
    Can't wait to hear it sing!

    Leave a comment:


  • E30-TourZing
    replied
    Thank you all for the input this far! I will be adding more details shortly, but I’ve been hard at it and here is a little teaser of my motor.
    Attached Files

    Leave a comment:


  • Hdx
    replied
    I was saying use a restriction instead of a pressure regulator. Don’t do both.
    the nodiz sounds great. I looked a the site, seems really reasonably priced to.

    some of the + and - running Dcoe carbs on the m20
    . Great increased performance
    . excellent reliability
    . simplifies the engine bay way less digitals .
    . Simple and easy to tune
    ​​​​​. great classic look
    ​​​​​​. incredible induction sound
    negatives
    . can get some fuel vapor smell in the garage after shutdown when hot.
    . fuel mileage tends to be higher.
    . No altitude compensation . You need to rejet and adjust idle mixture for best performance.
    . No ability to tune on the fly with passenger and laptop. Or auto tune.

    I like modern efi too . I have a e34 m5 with s38 running on ms and it is great but way more complicated and expensive to run .

    one of the greatest cars I ever had was a 79 e21 323i with a close ratio transmission, built motor , with three Dcoe 45s and a points distributor .

    Leave a comment:


  • E30-TourZing
    replied
    Originally posted by Hdx
    I have done it before with a high pressure pump. It can be really simple.
    just a restriction in the return line to the tank . install a brass straight barbed fitting . tap it so you can thread in a drilled grub screw . Start with a 2.5 mm hole . Adjust the hole size till you get around 3.5 psi at the carbs.

    I have had 3 Dcoe 45 Webers on my m20 for 25 years . They will work excellent. I prefer them over the fuel injection. I used a 323i distributor
    for years. Not a lot of room for the distributor cap but works good . I now Use electromotive xdi ignition. Waisted spark . Sadly now no longer available.

    I would just run really short stacks and the stock booster to start with. It
    will still run great. The longer stacks are nice but will only make a subtle
    difference.

    I don’t run a booster on my car and prefer it to boosted brakes. Not for everyone though . I find it much easier to modulate the brakes. Boosted brakes lock up to easy for me. I made my own set up similar to lees with a willwood mount https://www.ebay.com/itm/400328937249 .
    I use two 5/8” willwood masters With a remote adjuster in the cockpit to adjust the balance bar.

    45 mm carbs with 36 mm chokes works good on a stock
    2.5 engine . Good torque and will rev high .

    slightly higher float level and a slightly rich idle mixture
    are the secret to excellent off idle performance.

    Thank you for your input! I ended up buying a aeromotive FPR w/ return that goes to 3 PSI. Hopefully this gets me the numbers that I am looking for. Are you saying I should add a restriction even with the FPR?

    Unfortunately I didn't get the ability to add a booster and I added manual brakes to my car. I am sure it will be fine. I only use the car for fun spirited driving, it isn't a daily.

    For ignition I am going wasted spark with the NoDiz ignition module. I think its the easiest situation to go with.

    What are some of the positives and negatives you found with running DCOE's on your M20 for so long?

    Leave a comment:


  • Hdx
    replied
    Pic of short stacks on a m10 I just built I think may work. And clear your booster.
    Click image for larger version

Name:	IMG_1585.jpg
Views:	116
Size:	243.3 KB
ID:	10157087

    Leave a comment:


  • Hdx
    replied
    I have done it before with a high pressure pump. It can be really simple.
    just a restriction in the return line to the tank . install a brass straight barbed fitting . tap it so you can thread in a drilled grub screw . Start with a 2.5 mm hole . Adjust the hole size till you get around 3.5 psi at the carbs.

    I have had 3 Dcoe 45 Webers on my m20 for 25 years . They will work excellent. I prefer them over the fuel injection. I used a 323i distributor
    for years. Not a lot of room for the distributor cap but works good . I now Use electromotive xdi ignition. Waisted spark . Sadly now no longer available.

    I would just run really short stacks and the stock booster to start with. It
    will still run great. The longer stacks are nice but will only make a subtle
    difference.

    I don’t run a booster on my car and prefer it to boosted brakes. Not for everyone though . I find it much easier to modulate the brakes. Boosted brakes lock up to easy for me. I made my own set up similar to lees with a willwood mount https://www.ebay.com/itm/400328937249 .
    I use two 5/8” willwood masters With a remote adjuster in the cockpit to adjust the balance bar.

    45 mm carbs with 36 mm chokes works good on a stock
    2.5 engine . Good torque and will rev high .

    slightly higher float level and a slightly rich idle mixture
    are the secret to excellent off idle performance.


    Leave a comment:


  • E30-TourZing
    replied
    Originally posted by zaq123

    not advantage. Actually kind of a backwards move like going to carbs from FI. But if you are doing it to be old school/electronic free setup, dizzy is a must.
    I appreciate the input. It was neat to do a deeper dive on 123Ignitions products.

    My other situation is deciding on a fuel pressure regulator that has a bypass. My fuel pump and sending unit etc is all new (including the tank) and I really don't want to have to modify in a low pressure fuel pump if I can avoid it. Stock units 3-bar (40ish PSI) and DCOE's like it around 2.5-3.5 PSI. I have heard a FPR with bypass can work well with a high pressure pump, but I am all ears if that seems unfit for the job or that I will continually be chasing my tail.

    Any advise or experience here would be welcomed and appreciated!

    Leave a comment:


  • zaq123
    replied
    Originally posted by E30-TourZing

    Thank you for the share! I have been looking into these setups. Any advantages that you can mention towards this vs a coil system?
    not advantage. Actually kind of a backwards move like going to carbs from FI. But if you are doing it to be old school/electronic free setup, dizzy is a must.

    Leave a comment:


  • E30-TourZing
    replied
    Got my linkage working today -
    Attached Files

    Leave a comment:


  • E30-TourZing
    replied
    Originally posted by zaq123
    if you are doing carbs, might as well go this route for the ignition.

    Click image for larger version

Name:	123-tune-plus-bluetooth-bmw-320-6-520-6-m20-m60.jpg
Views:	128
Size:	115.0 KB
ID:	10154954
    Thank you for the share! I have been looking into these setups. Any advantages that you can mention towards this vs a coil system?

    Leave a comment:

Working...