Well, I Am Going To Add Triple Webers To My 3.0L M20…

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Panici
    replied
    To me this is very good number 44 hp over stock intake manifold
    Indeed those are great numbers!

    I wonder what a 2.5L would look like compared to the 3L. The extra 500cc must have really been choked down by the stock manifold.

    Leave a comment:


  • litu
    replied
    Originally posted by E30-TourZing
    On the dyno it made 44 hp more than the stock intake manifold at 6500 RPM.
    To me this is very good number 44 hp over stock intake manifold

    Leave a comment:


  • digger
    replied
    dyno.jpg not loading..............sounds really good. i am running my ITB open trumpet atm while i do some work as well and agree it is super loud.

    Leave a comment:


  • E30-TourZing
    replied
    Here is a quick drive by
    Attached Files

    Leave a comment:


  • E30-TourZing
    replied
    Hello Gang! Well my touring is offically and running and driving DCOE machine. It has great pull and has loads of character! The intake noise is so loud that I cant hear the exhaust past 4500 RPM. (Wasnt expecting this). On the dyno it made 44 hp more than the stock intake manifold at 6500 RPM.

    I still have some tuning to do and I need to setup my Vacuum and MAP sensor as the ignition will be more manageable for street driving. On and off throttle is choppy. I need to tap the intake runners, but my car is off to get repainted in a week or so which means it will be a later job.

    What was most surprising to me was the brake feel. I am running a boosterless setup with 5/8" Tilton MC's. Generally it feels like I would expect, but the ceramic pads I have on now do NOT inspire confidence when I need the brakes the most. I am curious what pads people are running with my exact setup. Its not a track car so I need something that bites right out of my driveway. Any input would be desired!

    Leave a comment:


  • E30-TourZing
    replied
    Last photo shows the condition of the over-exerted clutch slave cylinder
    Attached Files

    Leave a comment:


  • E30-TourZing
    replied
    I appreciate all the input on my clutch issues. I couldn't see any issues with my installation, so I made a new rod that was 1cm longer and it now works great. Still cant get the setup to stop squeaking. Anyone solved this issue before?

    Friday the car goes into my dyno tuners shop to have a new wiring harness built and then get the carbs working. (hopefully) - Then a new paint job in mid June and upholstery shop there after. Hope to be driving it in August completed. Lets see if it was all worth it haha.

    Leave a comment:


  • digger
    replied
    Presumably it is possible to extend if you have the parts/means

    Leave a comment:


  • E30-TourZing
    replied
    Looks like I need this throw out bearing - https://shop.bmw.ca/p/Bmw__/CLUTCH-R...511204525.html

    Think I could get away with extending the rod to match the distance between the late model TOB? It isnt much and I would wayyy rather do that vs taking off my headers/exhaust and dropping the transmission if I can avoid it.

    Leave a comment:


  • E30-TourZing
    replied
    Originally posted by digger

    what parts did you change and which did you keep while you were in there ? Over extension can be due to worn plastic pivot and badly worn throw out bearing
    Fair, I installed a new brass pivot when I replaced my flywheel with RHD one. I also did a stock late model Sachs clutch, pressure plate and flywheel at that time. It all has about 5,000-6,000 Km's since. Should all be in strong working order.

    Leave a comment:


  • digger
    replied
    Originally posted by E30-TourZing

    I super appreciate this info. This isn't my first rodeo and I am confident I put everything together properly.

    So it seems that my slave cylinder is over extending. I am not sure if the RHD flywheel is different than stock, so perhaps I need to add a CM to the rod to help it out. I just bought a new master cylinder and a slave cylinder and I will reassemble for there. I will also inspect with a camera.
    what parts did you change and which did you keep while you were in there ? Over extension can be due to worn plastic pivot and badly worn throw out bearing

    Leave a comment:


  • E30-TourZing
    replied
    Looks like my issue is that I am using a early model transmission with a single mass and the RHD flywheel. I should have used a E21 323i throwout bearing to compensate, but I will add some length to the rod and see where that sits. That being said it was the same setup before and It worked fine, so thats the only confusing part. I suppose it may have just been that the slave cylinder was able to work beyond its normal throw.

    Here is a page about what we are dealing with. -

    ​​​​​https://www.r3vlimited.com/board/for...ow-out-bearing

    Leave a comment:


  • E30-TourZing
    replied
    Originally posted by digger
    Well I can confirm the fork is symmetrical end to end so doesn’t really go in a particular way except upside down wouldn’t really work . Ideally if there is a clear measureable wear pattern caused by either the plastic pivot or slave then you put back in sane way but likely not a big deal
    I super appreciate this info. This isn't my first rodeo and I am confident I put everything together properly.

    So it seems that my slave cylinder is over extending. I am not sure if the RHD flywheel is different than stock, so perhaps I need to add a CM to the rod to help it out. I just bought a new master cylinder and a slave cylinder and I will reassemble for there. I will also inspect with a camera.

    Leave a comment:


  • digger
    replied
    Well I can confirm the fork is symmetrical end to end so doesn’t really go in a particular way except upside down wouldn’t really work . Ideally if there is a clear measureable wear pattern caused by either the plastic pivot or slave then you put back in sane way but likely not a big deal

    Leave a comment:


  • E30-TourZing
    replied
    Originally posted by digger

    i have one somewhere for a g260 i will see if i can find it later today. I am going by looking at pics on FCP/ECS atm for a new one not an original
    Thank you Digger! I really don’t want to have to remove my transmission. I am stumped to why it’s an issue at all. I was certainly careful on putting it together, but I don’t want to rule out that I made a mistake

    Leave a comment:

Working...