Cool wagon, aesthetically that's pretty much exactly what I would want...
I'd listen to the existing ITB and carb guys when it comes to bore, there are more issues than just lost low end with oversized carbs, they're harder to tune and have worse transient response at low rpm, I've seen this with bikes. You could easily use MS for spark only, and there is probably no benefit to running wasted spark over the stock ignition system on a street NA M20. My opinion is that it would take an insane build to run into issues lighting off the mixture NA, I've run a stock system with MSD coil in good condition with .020" gaps to over 15psi of boost, there are probably more posters in this thread than NA M20s which wouldn't run right with that setup. But keep the wasted spark if you have it already and like it, you can always retain your current standalone setup minus the fuel side.
If you do this, steer well clear of their single circuit brake master cylinder, it doesn't belong on any car street or track. To this day they still parrot the line on their website "Most OEM master cylinders are still single feed internally & have the same assumed “risk” to our Master Cylinder." which is just bullshit unless you consider "most OEM setups" stuff like pre-1967 VWs. I'd look into what 24V guys have done as far as moving boosters and undersizing them, clearance is always an issue with M5X swaps.
Well, I Am Going To Add Triple Webers To My 3.0L M20…
Collapse
X
-
Thank you for all your replies fellas! I am fairly secure on buying the Webco manifold even though there are some unknowns to me about how it is all finalized with the oil pickup and thermostat housing. Regardless it should work. Its also considerably narrower than IE's manifold. I am curious how the performance will differ between the two.
I have been processing the booster situation, and I am hopeful a e90 booster will be enough. Has anyone moved the booster location more to the drivers side with the E90 booster for even more room? Also looking into a chase bays manual booster, but I don't like the idea of manual brakes on a street car.
Would running 45's vs 40mm really hurt the torque so much where I might regret it? The 45's will give more jam up high, but I would like it to be fairly progressive in power as its not driven as often in the upper range due to speed limits. Input on this would be great. The Webco manifold is designed for 40mm carbs. So it would be easier on the entire setup if I ran 40mm's. I assume it would need machine work in order to host the 45mm opening. Apparently its 5 axis machine work. Something that might be difficult to sort out locally to me. (forgive my lack of machining knowledge)
https://www.dbilas.com/en/Intake-tra...le-carburetors - Any input on this setup along with the linkage?
https://dbilas.com/en/Carburator-sys...03.010.004S-45 - This kit is also quite appealing. I have emailed them to get more information.
As well, I have looked into ignition options. Technically I could still just use my Megasquirt setup no? This would also allow data logs so I can see mapping of my AFR's. Does the NoDiz setup offer me any advantages? Would I be best off to just run a cap and rotor setup again?
Thank you all for your input! I cant express how much I appreciate the community!
- Jan
Leave a comment:
-
No idea on the M20 manifold situation these days- triple Webers are fantastic, but not currently in vogue.
All I can add is that for a street- driven engine under 3 liters, 40's will probably be easier to tune at low loads.
You'll have less throttle plate area, and with a relatively small venturi, better idle and transition metering.
The throttle linkage is important- you can certainly do it yourself, but look up Hal's design on www.2002faq.com
for ideas on how to do it well.
DCOEs are their own beast.
t
Leave a comment:
-
what would you need a standalone for? on carbs the only thing it could do is time spark, everything else becomes irrelevant. the stock ecu should probably be able to handle spark. if you are running standalone i'd go straight to itbs, once you've tried setting up, tuning, and syncing triple webers you'll be more than ready to embrace itbs and digital tuning instead.
edit: try a couple e21 forums. that's where m20's and triple webers will be found and probably have more relevant info.Leave a comment:
-
What's the cost to ditch MS and go with a professional setup like Haltec? I don't know what it's like for a general consumer, but they seem pretty responsive to Mighty Car Mods. Being a major brand, you're likely to find more support for install and tuning.Leave a comment:
-
Brake booster clearance is largely determined by the angle of the manifold off the head and the total runner length as well as booster being used and if it has been moved.
With Webers you want the runner to follow the port centreline and then start to bend over so the actual Weber sit close to horizontal (for functional reasons) and as this would somewhat optimize booster clearance.
Skifree developed a setup for 2002, not sure how this translate to the e30. The e90 type booster improves things slightly plus its a better setup than the stock e30 booster
https://www.flickr.com/photos/152898...7688980425565/
with fuel injection there is much more flexibility in the designLeave a comment:
-
I appreciate your response 2mAn. For sure there is a solution available to keep EFI, but keep in mind this would also want to add ITB's after, so it would likely cost more to go this route. Carbs certainly are not going to be the best case scenario for effectiveness, but it is what I am leaning towards for a few reasons.
- Mechanically speaking, I built the car myself and I would like to continue that path. With carbs I feel pretty available to working on them once tuned. I spend time around vintage 911's often and it amazes me how little they need once dialed in. Year after year with little use of the car or cleaning, they start up after months sitting and two pumps of the throttle before turning the key. They also perform really well under all load conditions.
- They look and sound the business. I am into something unique as long as it functions. I really do not drive my touring often, and when I do I am about utilizing all it has to safely offer me on the street. (driven hard-put away clean)
- I have some carb wizards in my corner who offer great advise and assistance when it comes to these things. Less so with EFI tuning. My good friend who spawned my MS setup no longer lives in the same province and he is a new father which means its difficult to bug him when questions arise.
My hope is the oil tube from the head can safely lead to the block with this plate and that the booster can still be used (even if its a 944/E21 booster)
Can anyone chime in on this product and give there two-cents?
Thank you!
Leave a comment:
-
EFI is always going to be better. You're looking at an easy $2k for the manifold and 3 weber 45s and that money can be given to an expert to sort of your issuesLeave a comment:
-
Well, I Am Going To Add Triple Webers To My 3.0L M20…
Hello Gang!
Its been awhile since I posted. I finished my 3.0L M20 a few years back. The motor has been swell, but my standalone experience has been less than appealing. Exactly what I was hoping would not be the case.
2- year ago I ended up building an entirely new wiring harness from scratch (took roughly 42 hours to complete) and its causing some issues for me now. I recently left my career restoring cars full time and now have a job in a different industry that gives me zero time to spend time working on problem solving my Touring.
My plan with getting MS2 setup is to run ITB's. Based on my issues with electronics, and the fact I need outside assistance, I am looking to simplify my drivetrain while still having the sweet, sweet power and noise of ITB's. My original concept was to do side draft Webers before I was coached into a standalone, so this is my current direction.
I have done some research and based on my motor, DCOE 45mm Webers will be the best for the application. There is a mounting plate which is CNC'd and needs to be modified to host 45mm carbs, but the oil tube is clearly different and there isnt much documentation or opinions on this setup.
Here is the link to the plate - https://www.ebay.ca/itm/361433574358
I spoke with Webco in UK and Pierce Manifolds directly and neither one of them has any added value on the product. This add on is quite expensive to my motor and I want to be a sure as I can about where I am spending my money.
Does anyone have experience with this setup on an M20/E30? Because the profile is smaller, does it help clear the booster now? Are their any photos of the oil tube setup?
Thank you for all the countless times you guys have saved my bacon in the past!
(Photos are of my current setup)
5 PhotosTags: None🥰 1

Leave a comment: