ttrousdell's Project Thread (E30 M3 & S38 swap content)

[F34R]

Glad I got to make the trip up. Ill be back again with the e30 and more ammo. Ive considered that idea.

I'm glad you made it up too! was awesome having you and the GF here for the little bit you got to stay. You better bring the e30! I'll show you all our amazing country roads here.
Loved all the shots and work! you did the s14 right by cleaning and refreshing for seals/gaskets.

[DER E30]

Love all the M power in this thread!

[2mAn]

What are your thoughts on the tires? I need to get a new setup soon and I was planning on getting the 225/45s all the way around but I like the thought of 245s in the back

[ttrousdell]

What are your thoughts on the tires? I need to get a new setup soon and I was planning on getting the 225/45s all the way around but I like the thought of 245s in the back

The car hugs the road very well. I really like this setup. You can fit the 245s on the M3 so why not.

The 325is went through a lot of changes in the last few weeks. Mainly the swapping out of the S38. Ive grown really fond of my M3 with the S14. Going to try and make the car into a light good handling autox car for this coming season. I picked up this spare S14 so I decided to throw it in and see how I like it.

Some last photos and video before the swap...







Tore into it







Worked into the night to get the s14 in





Welding my rad support

Made brackets to hold the radiator in its final position. Oil cooler in position too. went with Mishimoto for both radiator and oil cooler.

For now ill be running mechanical fan with the shroud but will switch to an electric puller in time. Cutting the lines for the oil cooler to size. I just used a hacksaw to cut them. wrapped where I cut with duct tape to keep the fraying down. M18x1.5 to AN10 adapters needs on oil filter housing.

Oil Lines in place

Now the huge plenum from the s38 isnt in the way I can go back to assisted braking. Cutting the lines and flaring them to fit again.



Much better fit then the s38.


So I got the engine to start today so ill share the electrical side of things. To start this is a 89' 325is so again here is the body side of the C101 for that car.
89' M20B25 C101

1. Alternator Charge - BU
2. Oil Level Static- GN/YL, BU/BK
3. Not Used
4. Cool. Temp - BR/VI
5. Oil Press - BR/GR, BK/BR
6. O2 Heater - GN/WT, GN/YL -12V
7. Ignition Coil - GN - 12V
8. Fuel Rate(econo) - WT/BK,YL/WT
9. Tach Signal - BK
10. Oil Level Dynamic - BU, VI/GN
11. Inspection reset - WT/GN, WT/BU
12. Check Engine - GY,BR/BK
13. Fuel Relay - GN/VI,VI/RD 12V
14. Speedo- BK/WT,BU/YL
15. Unloader- BK/GN
16. SRS/Not used
17. ABS
18. Starter - BK/YL 12V
19. Not Used
20. Not Used

Now the 1989 M3 harness engine side C101. Which shares many similarities.

1. Alternator Charge - BU
2. Oil Level Ground - BR/OR
3. Not Used
4. Cool. Temp Gauge on Cluster - BR/WT
5. Oil Press light cluster - BR/GR
6. Diagnostic Port - GN/YL -12V & Evap Purge Relay BU/YL
7. Ignition Coil Primary - GN - 12V Power Main Relay-GN
8. Fuel Rate(econo) - WT
9. Tach Signal - BK
10. Oil Level to ground through resistor to pin#2- BR/OR
11. Inspection reset - WT/BU
12. Not Used
13. Fuel Relay - GN/VI 12V
14. Not Used
15. Starter Unloader- BK/GN
16. To Diagnostic Port- WT/BK
17. Not Used
18. Starter - BK/YL 12V
19. Oil Temp(M3)-BR/VI
20. Not Used

To get this to work I simply depinned #2 and #10 since they go to ground on the M3 and not on the 325 and plugged them together. #6 is different but they both are supplied by a wire of the same size with a 15A fuse.

Used the diagrams. Look up your car and look for C101 and next to it the pin #. Fairly simple.

http://www.armchair.mb.ca/~dave/BMW/e30/

Few more things to note when swapping the S14 to 325

• Throttle cable for s14 is longer M20 cable cant be used
• Tranny mounts and brackets are different.
• Motor mounts for S14 are taller.
• G265 Shifter parts are different than G260,G260/6, and G280.

Info on S14 bell housing sensors that i don't feel like re-typing

http://www.r3vlimited.com/board/showthread.php?t=348794

More to come now that the engine is running.

[ThatOneEuroE30]

Haha s38 to s14 swap in a weekend epic haha

[QuiqueUy]

This is amazing , i have just finished reading all your thread and its amazing.

Loved all the M power on this thread haha , keep up the good work !

Can't wait to see some videos with the s14 :p

[litu]

Cool

[jhaurimn]

Curious to hear how the s14 compares in the 325 compared to the m3.

[CorvallisBMW]

So what are the plans for the S38?

[rzerob]

So what are the plans for the S38?

He has it for sale.

http://www.r3vlimited.com/board/showthread.php?t=346630

This is one of my favorite threads. I don't know if I would have done S38 to S14 but when I read you got a S14 I assumed it was going in this car. It will definitely be more nimble on the track than with the S38. I am looking forward to video. Keep up the good job.

[elmandatario]

Nice I was wondering what swap you was gonna do. I like how you always refresh the engine before the swap nice work. Definetley gotta see it in person during the warmer months

[The Dark Side of Will]

Curious to hear how the s14 compares in the 325 compared to the m3.

Yeah, how much are the wider tires worth?

Going to run both at the same AutoX before you rip much out of the 325?
It's a 323 now, isn't it?

[F34R]

Seeing as you plan on SCCA I think the S14 was a bad pick since it is all top end and SCCA is low end power for slow and fast in first-3rd.

As always, love seeing you do what you do! Stoked to do some driving this summer :D

[GDA]

Man this thread is so full of cool.

Numerous S engines and pics to show they are well cared for and used.

Very cool

[goarmy]

E30 has to be soo much happier now without the boat anchor