S38 turbo e30 Hartge H35-24 H bomb

[e30m3s54turbo]

I finally bought my Mason Engineering aluminum lower e30 X brace. I will install it after I get my new Ground Control
coil over kit. I bought used e30 m3 struts for $500. I didn’t want to pull the ones on M car.

[e30m3s54turbo]

I installed my Tial 44mm waste gate. I need to order the exhaust piping to waste gate. I know the waste gate looks close inner finder. It has clearance.

[e30m3s54turbo]

If you do a standalone electronic boost controller down the road, I can't recommend the GFB G-Force III enough.
Not quite as convenient/adjustable as having it controlled by the ECU though (which I assume you would rather do, given the standalone.)

Thank you, for your advice on it. I will read up on GFB G-Force III.

[Northern]

If you do a standalone electronic boost controller down the road, I can't recommend the GFB G-Force III enough.
Not quite as convenient/adjustable as having it controlled by the ECU though (which I assume you would rather do, given the standalone.)

[e30m3s54turbo]

I’m going to install the springs on 44mm waste gate at 15 psi. I can always increase more with a boost controller.

[e30m3s54turbo]

I’m finally installed my custom cluster and tucked some wires on bottom of it. I still need to order a new kick panel.
one of parts came in today. My new 44mm Tial waste gate.

[e30m3s54turbo]

how hard was this to do? Where did you get the parts? The innovative goods ones seemed a bit pricey for $160

.
I bought my from My Classic Parts. It was easy to install. The price is $170.

[downforce22]

I finally finished up installing my rpm tach light on my cluster. I set up tack to go up 7,500 K.

how hard was this to do? Where did you get the parts? The innovative goods ones seemed a bit pricey for $160

[e30m3s54turbo]

I finally finished up installing my rpm tach light on my cluster. I set up tack to go up 7,500 K.

[e30m3s54turbo]

I ordered a new part for my custom cluster.

[e30m3s54turbo]

i've ran a few of those eBay coding plugs. you need to install the chip with a pair of needle nose pliers. they work just fine. i never wasted the time trying to modify a plastic e30 coding plug housing to work with the e28 coding plug. seemed like more work than it was worth, at the time.

Thanks, Austin for input.
Yes I bought eBay ones for e28 m5 8k chip. It was short and pin needles. I been watching your build on the s14 2.5 👍
I went back to to e30 Cluster site and order the 6 cylinder 8k chip $28 bucks. It fit perfect like the stock e30 cluster chip. The costume cluster was cheep to buy $450.

[e30austin]

i've ran a few of those eBay coding plugs. you need to install the chip with a pair of needle nose pliers. they work just fine. i never wasted the time trying to modify a plastic e30 coding plug housing to work with the e28 coding plug. seemed like more work than it was worth, at the time.

[e30m3s54turbo]

I ordered a 8000k cluster chip. The one ordered from eBay was to short to fit. It a e28 m5 cluster chip. I ordered two from E30 Cluster. It fit perfect…

[e30m3s54turbo]

They have carbon kick panels, You could just vinyl wrap or flock them.

Does the oil temp sensor read before or after oil cooler?

One oil temp is on top of oil cap filter. Where would be the best to place it?

[moatilliatta]

They have carbon kick panels, You could just vinyl wrap or flock them.

Does the oil temp sensor read before or after oil cooler?