1990 - 24v swap

[mjweimer]

I did the same thing with my auxiliary fan about a year ago, still going strong, better than any cheap aftermarket fan.

100% - a little time, $12 for the bearing and good as new.

[jsta1109]

I did the same thing with my auxiliary fan about a year ago, still going strong, better than any cheap aftermarket fan.

[mjweimer]

Late August into September of 2020.

To finish up the wiring and before the front valence could be re-installed, I needed to install the condenser and condenser fan. Updating to the parallel flow condenser makes sense at this point so I sourced the Nissans piece and found (like many others) that the fan mounting brackets were not installed properly. They were not backwards like others have found but the fan would not fit.

So I drilled out the rivets, fit the fan in place, marked and drilled new holes and then secured the brackets with bolts/nuts/loctite.






When spun by hand, the fan was a bit crunchy with some resistance...so I took it apart to investigate. Worst case, it was junk and needs replaced, best I could service something like the brushes or bearing.

A LEFT HAND Threaded nut holds the fan blade to the motor shaft and when removed allows access to the motor bearing. The bearing cover is spot welded on the housing so some careful drilling allowed it to be removed. The bearing was dry and had some rust, interestingly it is not a sealed bearing.






The bearing was an SKF part and had a part number on the housing (6001) and thanks to their excellent online catalog, I was able to cross-reference to the same type of bearing in a sealed configuration.



Some tack welds and a bit of paint finished up the job.




All mounted up.




To appease the neighbors and my ears, it was time for a proper exhaust. Thanks to Scott at Stromung, I was able to get their E30 catback muffler modified with a single 2.5" inlet with a slight downturn to clear the subframe. My buds at the local muffler shop took care of the rest.






The exhaust turned out great, I had no idea if it droned at this point because the interior was gutted.

[mjweimer]

Back to the updates. Now August of 2020.

As mentioned previously the car was experiencing some strange running symptoms and finally set a code for the cam position sensor. I could repeat the symptoms by pushing on the cam position sensor wiring. Swapped out the cam and crank sensor (for good measure) and this is what the cam sensor wiring looked like when I tugged on the harness...nice.





The ICV hose fit but it had a slight kink that was pushing it into the charcoal canister. I don't like things to rub so the decision was made to cut the stock M52 hose and clock it slightly, reassembling with another ICT billet barb fitting.




Plenty of clearance.






Fit up the Air filter, MAF, etc. for the final time and made a little shield out of silicone scrap to keep the fan wash out of the filter inlet.






To keep the exhaust from blowing back on the fuel tank and try to reduce the noise in the cabin, I added a temporary downturn.




Another clearance issue to address, the upper radiator hose (stock E36) was touching the oil filter housing when it was under pressure, a quick trim took care of the problem.




Working around the air filter housing reminded me that I still needed to install the cruise control cable. The late M50 cruise control cable (9/94 onward - p/n 65 71 8 380 076) has the right fittings on each end for the E30 cruise module and the OBD1 throttle body.








And finally, I HAD to take care of the tramp stamp someone painted on the trunk lid way back when...as you can see by the left side a bit of acetone took care of it easily.

[mjweimer]

I'd show up? Is the Purple Touring allowed?

Absolutely! I'm looking forward to checking out your touring. Hopefully we can get something together in the spring.

[twright]

All of our CCA events are always on the NE side of Indy and usually attended by the same folks who live in the area (coincidence?). I know there are folks with older stuff who would like to do something even if it is a simple meet-up.

I'd show up? Is the Purple Touring allowed?

[mjweimer]

A GTG is like pulling teeth but nice to see it one come together. Maybe piggyback off a BMWCCA event.

I looked for a nice set of crimson cards for a bit. Hard to find and most are 4 door... Red is hard to photograph.

Zach

All of our CCA events are always on the NE side of Indy and usually attended by the same folks who live in the area (coincidence?). I know there are folks with older stuff who would like to do something even if it is a simple meet-up.

[moatilliatta]

A GTG is like pulling teeth but nice to see it one come together. Maybe piggyback off a BMWCCA event.

I looked for a nice set of crimson cards for a bit. Hard to find and most are 4 door... Red is hard to photograph.

Zach

[mjweimer]

That is a good question. BMW shows two different part numbers for the multi-piece foam insulation for the M10, M40 and M20 cars.

Up to 8/89 = 51 48 1 972 245 and after 8/89 = 51 48 8 103 798

It is a smooth texture that also has small perforated section in the center panel that can be removed to gain clearance at the top center of the engine. My Euro '86 325i had this panel removed to clear the very top/center of the intake manifold where the small vacuum line connects (opposite the throttle body).

I don't know if the M42 hood insulation would clear this area or slightly rub.

[82eye]

Appreciate the kind words.


The under hood insulation is the OE pieces from the '90-'91 318i/iS - part number 51 48 1 925 437

cool. i like it more than the standard cardboard. wonder it it would work on a regular 325i.

[mjweimer]

I though all cardinal interior had window crank plugs, 88+ was cherry or Crimson.

Cool, I'm in southern Indiana, but work in the "Ville"... I'm about start some winter refinements on mine so It'll be out till spring. But it would be cool to try and around up some regional E30's next year for a GTG. It would be great to see this in person.

I ran into some Indy area E30 guys heading back from brodeo few weeks ago. surprisingly!!

Yep, I lazily call all E30 red interiors Cardinal but in reality this is the 0324 Karmesinrot/Crimson red leather. I think the change was with the 9/89 onward production through end of the model run and this car is a 3/90.


I'd be up for a GTG and there are several folks from the Indy area that would likely be interested as well. Sure would be nice to have some more vintage BMW events in the area.

[moatilliatta]

I'm about halfway between Indy and the 'Ville. The interior is the original Cardinal red leather...for some reason it looks really red in those pics.

Yeah, a snafu with Flickr lost all the pics that were linked in the thread. It will take some time to get that sorted.

I though all cardinal interior had window crank plugs, 88+ was cherry or Crimson.

Cool, I'm in southern Indiana, but work in the "Ville"... I'm about start some winter refinements on mine so It'll be out till spring. But it would be cool to try and around up some regional E30's next year for a GTG. It would be great to see this in person.

I ran into some Indy area E30 guys heading back from brodeo few weeks ago. surprisingly!!

[mjweimer]

stupendously gorgeous.

what is the product you used for under hood insulation ?


edit : white is one of my favorite colors on an e30. it's one of the few cars that can wear it well.

Appreciate the kind words.


The under hood insulation is the OE pieces from the '90-'91 318i/iS - part number 51 48 1 925 437

[82eye]

stupendously gorgeous.

what is the product you used for under hood insulation ?


edit : white is one of my favorite colors on an e30. it's one of the few cars that can wear it well.

[mjweimer]

A thing of beauty. Fantastic work, Mr. Matt!

Always appreciate the kind words.

Looking good! What part of Indiana are you in?


Cherry interior?


It looks like your previous photos went missing.

I'm about halfway between Indy and the 'Ville. The interior is the original Cardinal red leather...for some reason it looks really red in those pics.

Yeah, a snafu with Flickr lost all the pics that were linked in the thread. It will take some time to get that sorted.