SoCal General Chat

[Tanner]

anyone know a spot where I can get my konis revalved?

I lowered the 6 to where I want it but now its a bit too stiff

we might be able to. I'll double check with our damper department tomorrow morning.

Have you contacted Koni yet? If not, I have a direct contact there that I can ask if they revalve locally.

[JFarhanbod]

we might be able to. I'll double check with our damper department tomorrow morning.

Have you contacted Koni yet? If not, I have a direct contact there that I can ask if they revalve locally.

havent contacted them yet mostly because they say itll take them at least 6 weeks and I cant have the car down for that long.

I'm currently using stock koni yellows with 700lb springs all around, probably going to step the front up to 750 soon

[mcr_driver]

This 86 eS/iS I have been putting together is going to be a very nice car for somebody. Just finishing up a complete front end overhaul... Struts, ball joints, M3 control arm bushings, tierods, hubs with bearings, M3 springs, rotors, and pads.

Moving on to the rear next! Already did the IE subframe and trailing arm bushings. Now to install new wheel bearings, rear shocks, rear shock mounts if needed, and E30 M3 springs. I think the rear brakes are OK but I'll do them if I need to!

Goal is to build the ultimate DD E30 for somebody.

Gib u bout tree fiddy foh et

[nickflic3]

Is it an es or an is? Sounds like what I need right now... Somebody buy my e28 :(

[E30_Pare]

What a 1000hp m20 looks like.

http://www.speedhunters.com/2013/05/...turbo-bmw-e30/

[MR 325]

Is it an es or an is? Sounds like what I need right now... Somebody buy my e28 :(

eS with 2.5 swap done right. It's getting a port/polish head in a couple weeks too.

[mcr_driver]

Define right for clarification?

[2mAn]

yea that can either mean "I" pistons and 885 head or eta bottom and 731 head. both would be right IMO

[mkcman17]

so a few weeks ago my door lock fell out of my door...





i took a chance at trying and bought a rebuild kit off pelican...was worried i would mess up the order of the tumblers or something but i have a brand new door lock now! crisp as helllll. all the instructions were in german though...

[einstein57]

Please ignore me because i'm to lazy to use r3v's abundant resources

fixed

[mod_junkie]

My car is hesitating in the high rpms when I stomp on it. anyone know what would cause this?

[E30_Pare]

they should of all been numbered & different sizes. So easier than it seems.

[ToPLeSS(e30)FeinD]

my car is hesitating in the high rpms when i stomp on it. Anyone know what would cause this?

cpssss!!!!!!!!

[MR 325]

Define right for clarification?

It has a M20B25 swap. It's done right because it wasn't done R3V style. Engine completely resealed, all sensors new, all new hoses, everything new that should be new! Here's an idea of new parts on the car so far... next up is the BimmerHeads cylinder head! (We're using the car for before/after dyno numbers).

Engine:
Rear main seal
Rear cover gasket
Oil pan gasket
Timing belt
Timing belt tensioner
Water pump
Thermostat housing gasket
Thermostat
Coolant sensor (gauge)
Coolant sensor (ECU)
Oil pressure switch
Oxygen sensor
Alternator belt
Spark plugs
Distributor cap
Ignition rotor
Valve cover gasket
Rocker shaft plugs
Exhaust manifold gaskets
All coolant hoses
Aluminum radiator
Fan clutch
Throttle body gasket
Pilot bearing
Fuel filter
Engine mounts
Oil drain plug
Oil drain plug washer
Oil filler cap
Breather hose
Injector o-rings
Fuel pressure regulator o-ring
Engine bay fuel lines
M20B25 exhaust system
GE silicone intake boot
3.73 LSD

Transmission:
Throwout bearing
Trans input shaft seal
Trans output shaft seal
Transmission mounts
Selector rod joint
Shift carrier bushing
Shift lever bushing
E60 545i short shifter
Selector rod clips
Selector rod washers
Lower shift boot
Upper shift boot

Suspension:
IE street subframe bushings
IE trailing arm bushings
Meyle complete tierods
Moog ball joints
M3 offset control arm bushings
Front wheel hubs/bearings
Rear wheel bearings
Front brake pads
Front brake rotors
E30 M3 springs
KYB struts/shocks
15x7 iX basketweaves
225/50 Toyo tires
15mm H&R spacers

Appearance:
Late model front valance
Fog delete panels
Late model i lip
US ellipsoids
Euro grilles
Euro plate filler

[E30_Pare]

jebus. what are u asking for it?