Just ban me now.
Announcement
Collapse
No announcement yet.
Post Your M/S5X 24V Swap Setup
Collapse
This is a sticky topic.
X
X
-
Originally posted by Nick_S View PostRe-posting mine since I'm done and it's running now.
1. Engine- 92 e36 M50NV. E34 pan and pick up All stock for now. A/C & PS delete.
2. Engine Wiring- E36 harness, adapter from Nando. 403 DME, Dinan Chip
3. Drivetrain- G240, M42 dual mass flywheel, OE M42 Sachs clutch, G240 TOB and slave, 4.10LSD, E30 mounts. e36 325i driveshaft
4. Shift Lever and Linkage- euro 320 shift arms, UUC shift lever, new bushings
5. Motor Mounts- E28 green mounts, E36 mount arms
6. Brake Booster- stock, bone stock. Not even moved. Clearance is tight, about 1/4in but it doesn't hit it so why bother?
7. Steering System- E30 rack with condor PS delete plate.
8. Cooling System- M42 radiator, new thermostat and 80C aux fan switch. Will be running a spal pusher eventually
9. Exhaust System- OBD-1 headers to E36 y-pipe. Had my existing exhaust trimmed and bent to meet the y-pipe. Super super simple. New bosch 02 sensor.91 318is M50 swapped
05 Honda Pilot
24V swap thread
http://www.r3vlimited.com/board/showthread.php?t=302524
Comment
-
1. Engine
S52B32: fully functional obd2.
Stock s52 cams (intake/exhaust)
rebuilt/flow tested/ultra sonic cleaned pink top injectors
E39 528i fuel rail with built in FPR (I can run the vanity cover, no problem, with no modifications. Awesome part but super hard to find)
3" stock MAF
K&N 9in cone filter
e34 oil pan with stock baffle
Red locktite'd and safety wired oil pump nut
2. Engine Wiring
RobertK @ Kadunza rewired my E36 wiring harness. Easily the best part of the swap. Everything was labeled, and stretched to the proper lengths to insure proper fitment. Fired up literally first try with no CEL's.
3. DME
Dave Markert @ Markert Motorworks reflashed my DME.
We removed...
-SAP
-EWS
-muffler valve
-vehicle speed signal requirement (for 87 325i/iS)
-bumped the redline
4. Drivetrain
Getrag 260, fully resealed and hot tanked.
M20 single mass LTW flywheel (11lbs)
Sachs Spec 2 M20 Clutch and Pressure Plate. rated for 400hp
E30 325i throw out bearing and pilot bearing
E30 325i clutch slave cylinder
E30 325i clutch master cylinder
E30 UUC Stainless Steel Clutch hose
Custom trans brace
E21 Trans Mounts
Manual e30 driveshaft new CSB and Guibo
3.73 LSD (70mph = 2,900 rpm)
5. Shift Lever and Linkage
UUC Evo3 shifter
UUC DSSR (with 10degree twist)
late model selector rod joint (to fit DSSR)
Garagistic Delrin bushings, front & Rear
ZHP Shift knob
6. Motor Mounts
E28 M5 Motor Mounts
7. Brake Booster, Master Cylinder, and External Reservoir
Zionville Reman'd E21 booster
E32 25mm Master Cylinder...going back to stock 325i. With the smaller booster, and bigger cylinder, the brakes are harder than Peter North's dick...seriously, not good for daily driving
318iS brake booster check valve
8. Steering System
Stock e30 steering rack
New E30 power steering lines
E36 power steering pump and reservoir
9. Cooling System
M20 late model radiator
Normal M20 spider hose.
80C thermostat
OEM Aux fan with 80C temp switch
10. Exhaust System
Stock OBDII exhaust manifolds
Downpipes cut at flange and rewelded onto custom downpipes.
2.5' single piped exhaust
Vibrant ultra quiet resonator
Vibrant 1040 street muffler
-Brad, AlphaTeam Motorwerks, LLC
91' 318iS - S54/6MT Swapped
08' E90 M3 6MT - Daily
04' Chevy Duramax CCLB - Work Truck/Hauler
Originally posted by IronJoe
Alpha Team: running through e30s, gringo icebergs, and 19 yr olds.
Originally posted by 2mAn
Brads a standup guy even though he likes buttsex
Comment
-
Engine- 95 s50b30 completely rebuilt, CP Pistons, arp hardware, achillies motorsports oil pump shaft
Engine wiring- E36 harness with 318 wire cover wired by kadunza. red413, Dinan Chip
Drivetrain- ZF that came with the s50, e30 driveline, revshift guibo adapter, e21 mounts with aluminum cups
Shift Lever and Linkage- Nardi shift knob, AC Schnitzer short shifter, new bushings
Motor Mounts- E28 mounts, E36 mount arms
Brake Booster- E21 booster with stock madter, abs deleted
Steering- e30 rack, PS delete
Cooling- m42 radiator, electric pusher fan
Exhaust- stock obd1 manifolds I will be using a aftermarket catco cats with magnaflow muffler hopefully it will pass bar inspection!
Comment
-
Post Your M/S5X 24V Swap Setup
S52b32: Obd1 converted
Obd2 fuel rail
Obd2 throttle body
Elring headgasket
Arp head studs
Recut valves & guides
Vortech V2 S trim w/ straight cut gears
6" crank pulley + 3" drive pulley = 15psi @ 7k rpm
ESS Supercharger bracket
Sillicone intakes water-air intercooler
Rally Road oil cooler cap
Earl's 6AN oil cooler
Walbro 400 E85 Fuel pump
318is transfer pump
Fuelab 6 micron e85 filter
1/2" aluminum fuel feed line
2. Engine Wiring
S50 manual harness
Early model 17 pin c101
3. DME
506 DME
RK Tunes chip
4. Drivetrain
Zf320
E21 trans mounts
eBay 11lb flywheel
Oem Sachs PP / Clutch - still holds 400wtq 😎
Oem Guibo
E36m3 manual driveshaft
2.79 LSD from a 325es
5. Shift Lever and Linkage
AKG dtm style chassis mounted shifter
Stock single shear linkage
Shifter brass bushing, trans rubber bushing.
6. Motor Mounts
E28 M5 Motor Mounts raised 1/2" with spacers
7. Brake Booster, Master Cylinder, and External Reservoir
Porsche 944 booster
325e non-abs master cylinder
Stock reservoir
Rear line lock for sweet burnouts
8. Steering System
E46 325i ZF steering rack, same ratio as 330ci
Relocated steering reservoir
E36 power steering pump
9. Cooling System
Koyorad e36 m3 radiator
Stock e36 thermostat
SPAL 16" pusher with 88C temp switch
Relocated e30 expansion tank
10. Exhaust System
Raceland 24v swap manifolds
H pipe
2 Walker '95 e36 cats
Y pipe
3" eBay resonator
Borla XS muffler
Sent from my iPhone using TapatalkLast edited by pandaboo911; 01-09-2016, 06:40 PM.
Comment
-
Post Your M/S5X 24V Swap Setup
Originally posted by sneakyRedPanda View PostThat relocated late model coolant reservoir is absolute money. Did you have to fab mounting points or is there an easier way? Where do you run the lines?
Yeah some angled aluminum and the original black tab thingy?? holds it down. The aluminum is fastened to the battery tray. The hose runs behind the engine, over the trans bell housing. The overflow runs through the wiper/blower motor area. Just some rubber hose wrapped in fire sleeve.
Sent from my iPhone using Tapatalk
Comment
-
1. Engine
S52B32: OBD I converted
TMS 24lb injectors
3.5" Bosch 800 MAF
e34 oil pan with achilles baffle + welded oil pump nut
2. Engine Wiring
95 M50 harness
wired by myself
3. Drivetrain
ZF 320 manual trans and driveshaft from a 328i
ebay f1 stage 3 clutch and chromoly flywheel
E36 m3 clutch slave cylinder
E30 325i clutch master cylinder with brand new hard/soft line
E30 UUC Stainless Steel Clutch hose
UUC poly transmission mounts
3.73 LSD
4. Shift Lever and Linkage
z3 shifter with akg shifter bushings and dssr
Condor shift knob
5. Motor Mounts
AKG poly
6. Brake Booster, Master Cylinder, and External Reservoir
E30 booster (shoulda went porsche...oh well)
E30 master cylinder with stock reservoir
M50 manifold was modified /shaved for extra brake booster clearance
7. Steering System
e36 m3 rack
8. Cooling System
mishimoto e30/e36 aluminum radiator
m52 coolant hard pipe
16" spal puller fan
9. Exhaust System
ebay headers
custom 2.5" exhaust being mocked up now.Last edited by s14brent; 06-28-2016, 11:48 PM.89 325i 4dr s52
02 BMW 525iT m54b30/manual swapped (daily) *sold*
21' Toyota Tacoma TRD OR 4x4 6 speed Manual
Comment
-
1. Engine- Euro s50b30
2. Engine Wiring- E36 M3 custom adapted 075 DME, Alpha N Tuning
3. Drivetrain- E36 M3 ZF 5 speed. E36 M3 dual mass flywheel, 2.93 LSD, Rebuilt driveshaft
4. Shift Lever and Linkage- previous owner short shift kit install.
5. Motor Mounts- AKG S50 poly mounts
6. Brake Booster- e28
7. Steering System- E36 M3 Steering Rack
8. Cooling System- E36 M3 radiator, not running stock oil cooler.
9. Exhaust System- Ebay headers with custom fitment, hiflow cat (unable to fit euro headers without more work). Fuelmiser o2 sensors.
10. Intake System- Custom Carbon Airbox with built in filter. Alpha-N mode, not using MAF.Save
Comment
-
Post Your M/S5X 24V Swap Setup
So my car is a work in progress as I am also doing big turbo in my GTI. Here's what I have so far.
Car: 1991 318is
Donor: 1999 M3, 143k perfectly running car
Parts taken from: 1999 Z3 2.8, E34 525i, E36 328i
Engine
- S52B32 OBD1
- M50 Manifold
- M50 Fuel Rail (considering switching back)
- Pink Injectors
- E34 oil pan
- Some ghost tune I had a buddy flashed with EWS delete
Engine Wiring
-Andrew's wiring harness adapter. Car was auto so will be getting rid of extra wires.
Drivetrain
- Z3 2.8 ZF trans. Stock clutch, flywheel and pressure plate.
- Z3 2.8 LSD 3.15
Suspension
- E36 M3 5 lug conversion up front(not installed)
- Z3 2.8 rear trailing arms(not installed)
- Eibach lowering springs(not installed)
- SACHs rear struts from a E36 328i
- E36 328i generic rear strut brace
Mounts
- Condor Bushings Engine and Trans. Having difficulty aligning the engine mounts but will try again soon.
Braking
- E36 M3 Front Brakes (Hubs, rotors, calipers, pads)
- Z3 Rear Brakes
- 944 Brake booster ( had the stock clevis welded to it)
Steering System
- E36 M3 steering rack with fresh tie rod ends. No spacers were needed however I have to shave the steering rod hole at the bottom. It was touch slightly.
Cooling System
- Mishimoto E36 radiator. Plan to run an E-fan in front of the condenser.
- E36 M3 hoses for now.
Exhaust System
- EBay SS headers
- Remus muffler
Sent from an AbacusLast edited by Yezus_Krys; 09-10-2016, 05:44 AM.
Comment
-
Originally posted by spiDmang View Post10. Exhaust System
Stock OBDII exhaust manifolds
Downpipes cut at flange and rewelded onto custom downpipes.
2.5' single piped exhaust
Vibrant ultra quiet resonator
Vibrant 1040 street muffler
Comment
-
Curious on avg price for this swap/build
Looking to swap the e30 still figuring out my path. Depends on what I can get my hands on! Also what anyone would recommend. Find an s5x full setup or build from m52 block?sigpic1989 Cirrusblau Metallic Sedan
S5X build in the making
More Doors More Love
Comment
-
Originally posted by jotam3 View PostHow do you like your exhaust setup? I'm gonna be at that step soon, S52 with stock headers. And have similar parts, Vibrant 1149 Muffler and Vibrant 1141 2.5" Ultra Quiet Resonator and wondering how it's going to sound. I was originally planing on going from the headers to two individual 2.5" pipes with an x-pipe, then the two pipes to a Y-pipe and into the resonator, and single pipe the muffler. But, if yours sounds good, I may be able to mimic yours instead.
+1 I would like to see some pics of the modified manifolds and custom downpipes. Also very interested in the noise level with this set-up.
The exhaust manifold to downpipe connection is the only area of my M52 swap I have not quite figured out yet.
Comment
-
Originally posted by mjweimer View Post+1 I would like to see some pics of the modified manifolds and custom downpipes. Also very interested in the noise level with this set-up.
The exhaust manifold to downpipe connection is the only area of my M52 swap I have not quite figured out yet.
https://www.facebook.com/TheArcAsylum/
Comment
Comment