How To Guide - E36 Steering Rack Swap

[dude8383]

heat will certainly help! try to get a chisel in there so you can spread the knuckle apart. when in doubt heat it out lol...

[TrentW]

Speaking of knuckles...

Can't get the steering knuckle loose from the steering column shaft. It's been two 5-6 hour days soaking with PB Blaster, spreading the clamp end gap wide as possible, prybar between knuckle and firewall. Don't want to pry TOO hard that way though.

Maybe heat?

Search failed to uncover solutions.

Advice?

[djmossm42]

Yep just modify the firewall, here's a good write-up http://www.rmeuropean.com/bmw-e30-steering.aspx

My post with a few other sources, I went with an E46 M3 rack but same things apply to all airbag cars and rack swaps.

http://www.r3vlimited.com/board/showthread.php?t=374017

Sent from my MI 4LTE using Tapatalk

[noahsense]

[QUOTE=Moriglioni;4558992]Anyone have a weird steering rack like this? '93 cabrio


That's just the knuckle for an airbag car, 1990-93. No modification to the knuckle necessary but you'll need to either modify the firewall slightly or build a custom knuckle.

[Moriglioni]

Steering knuckle**

Sent from my SAMSUNG-SM-G890A using Tapatalk

[Moriglioni]

Anyone have a weird steering rack like this? '93 cabrio


Sent from my SAMSUNG-SM-G890A using Tapatalk

[noahsense]

Thanks, I needed to confirm cause I already have my e30 hoses ordered and it would be a hassle to reorder e36 ones.

You'll find that this is a really sturdy part. I'm a skinny dude so I had to clamp it in a vise (w/ soft jaws or wood) and put some weight into it. Remember, adjust, test fit, repeat.

[marcusw]

You have asked this question in a few places, the answer is no. It worked for many people. If you are fearful of it, on a case by case basis, replace it.. your car.

Thanks, I needed to confirm cause I already have my e30 hoses ordered and it would be a hassle to reorder e36 ones.

[estoguy]

I said knuckle but I really meant flex disc/joint! Around $100 so not cheap but worth doing while everything is apart since getting it off can be a god awful pain.

I got a used one from a used BMW parts specialist outside Toronto for $50. It was a nice clean unit.

Getting out the old one was a bit of a pain. I would have done the engine lift thing, but didn't have one, so I did the bend-the-steering-rack-tab thing. It worked out pretty well after that.

[TimeMachinE30]

You have asked this question in a few places, the answer is no. It worked for many people. If you are fearful of it, on a case by case basis, replace it.. your car.

[marcusw]

Like i said a few pages back, I used my stock lines, I put the straight fitting on the power steering pump and the u shaped end on the rack. I had to open up the u shaped arch about 20-40 degrees but otherwise the stock lines fit without a problem. I was waiting to reply because I was going to take a picture for you.

Would bending the HP hose possibly cause the hose to break or leak easier?

[noahsense]

Good tips there! How much are knuckles going for these days?

I said knuckle but I really meant flex disc/joint! Around $100 so not cheap but worth doing while everything is apart since getting it off can be a god awful pain.

[roguetoaster]

Good tips there! How much are knuckles going for these days?

[noahsense]

How To Guide - E36 Steering Rack Swap

Just completed installation of an e46 purple tag rack [7852974678] and couldn't be happier. The steering is perfect and splits the difference between the standard e36 rack and some of the more aggressive racks. I think my turning circle shrunk too! Rackdoctor was great.

My car has an airbag so I had to modify the firewall; as someone else mentioned, a Dremel with tungsten carbide cutter [#9903] works well and since I broke the bit half-way through I'm glad that I had a spare. A flex shaft is absolutely essential if the motor is in the car and you’ll find it easiest to route from inside. A respirator is good insurance since the bit will turn metal, paint, and rubber into fine airborne particulate.

Other tips:
-Have a new steering knuckle/flex disc ready since the old one will definitely be showing wear.
-It’s not mentioned much but the slot in the knuckle/flex disc should align with the little divot on the steering rack shaft.
-While everything is apart on an airbag car, apply a good deal of Loctite Blue (avoid Red unless absolutely necessary) to the blue section inside of the the ‘Big Nut’ on the steering column. The Big Nut has an inner plastic thread locker which after one dissassembly is much less effective and tends to loosen and cause steering column shake over bumps. This really should be a one-use part but BMW never sold it alone.

[noahsense]

How To Guide - E36 Steering Rack Swap

On an airbag car, is it possible to install the steering joint upside down? I'm curious if this would move the shaft enough to avoid cutting the firewall.

[update] should be obvious to anyone who has done this swap - splines are a different size on each side