Originally posted by marshallnoise
View Post
I worded it wierd, I should say "like we want".
-
It was late and I matched them up thinking they were the same diameter, then looked at the clutch pads and went, oh. ha.
I worded it wierd, I should say "like we want". -
Ohhhh hahaha. I was wondering how your expectations wwerent even close to reality regarding the flywheel.
You are really moving along man. Awesome progress.
Sent from my SPH-L710 using TapatalkSi vis pacem, para bellum.
New Hawtness: 1995 540i/6 Claptrap
Defunct too: Cirrusblau m30 Project
Defunct (sold): Alta Vista
79 Bronco SHTF BuildComment
-
Ya, it gets late quicker than you think, before you know it, its nearly morning time.Comment
-
Just grabbed condor diff and rear subframe mounts, akg e30 m3 trans mounts, and also an e36 rack spacer kit.Comment
-
Condor has amazing customer service btw, there was a tiny mistake with my order/product.. I'm getting product overnight coming in tomorrow guaranteed by 3pm!
Did get this though, its super cool, I can barely see the bottom half of my beer!!!
Comment
-
^good beer choice!Comment
-
I love the piney tasting finish.. Reminds me of the Pacific Northwest.Originally posted by CorvallisBMW View Post
Too bad I get off work an hour after laurelwood actually closes.. It's called "northwood" now but I live maybe 3 minutes from their battle ground location.Comment
-
Popped over to my friends place, had a BBQ/Shrimp boil and got down on some minor car work!
The flywheel is off getting bead blasted and resurfaced, and I'm busy making sure the little parts are in check.
AKG, Condor, Ireland engineering, Garagistic, G-man, Revshift are All making an appearance in this swap.
You didnt need much light to see the awesome cross hatching this motor still holds, its nearly excessive.. ha! Everything looks good!
Small leak from crank sensor mount, and crank seal getting replaced after we get a seal puller.
This will be possibly bead blasted and resprayed.. atleast resprayed, I as hoping for a matching delphin metallic, maybe darker.
Comment
-
Resurfaced e28 single mass flywheel for m1.3
Comment
-
Purdy!
Sent from my SPH-L710 using TapatalkSi vis pacem, para bellum.
New Hawtness: 1995 540i/6 Claptrap
Defunct too: Cirrusblau m30 Project
Defunct (sold): Alta Vista
79 Bronco SHTF BuildComment
-
Great choice on the FW, you'll love it!Comment
-
Makes me want to resurface mine...Comment
-
Cost me $55, and hes in Hazeldel. that was for bead blast and resurface... I think just a resurface is $35Originally posted by SketchyRex View Post
Dowit!Last edited by the imitator; 04-25-2014, 01:57 AM.Comment
-
Got some more stuff in the mail today, I finally have my clutch setup in full.
Single mass flywheel
M5 clutch
M5 Pressure Plate
Throwout bearing
All Sachs Products :)
We also got the Rear main seal, crank seal, and oil pan all installed and ready for action!
scarping rear mainseal mating surface
newcrank seal
Comment
-
sorry for the quick foggy pics, we got my early model in and made super quick work of the suspension.
Finally dug around enough and found a place in the floor board where i could jam a flat head through the rust, also a small area where the battery will no longer sit inthe engine back, and one more spot by by the windshield. all this was minor.. nothing excessively rotted or anything to be bummed out about.
1.Strip and respray some of undercarriage
2. make it a roller on monday with all the cool parts :)
Last edited by the imitator; 06-02-2014, 01:59 PM.Comment
Comment