What exhaust was that Ti running?
Announcement
Collapse
No announcement yet.
Markert Motor Works Dyno Thread (many inside)
Collapse
X
-
AFAIK, Ebay headers and a nice 2-1 merge (2.75) and vibrant mufflers... wasnt terribly loud
Check Us out on Facebook
Needing a harness adapter or wiring help? Check it out: also have 24v motor mounts, E30 M3 covers and E36 ECU mounts!
Full Product Line Tuning
OBD2 Tuning Available! OBD2 E36, S54 Swap, S62 Swap, etc: tuning@MarkertMotorWorks.com Dyno Thread
Comment
-
Originally posted by 328ijunkie View PostUpdate 4/7/15
No tuning here, just a dyno to dyno comparison... Car is an M52 318ti, M50 manifold, S52 Cams, Headers, Exhaust, 3.5" MAF, BBTB
A shops dyno in atlanta with their tune on it:
Same car same tune on the dyno we use (Switched run to SAE because the other shops dyno is run on SAE):
STD Run:
i went through data for 9 other "stock" E46M3 dynos on a DJ getting rid of the outliers that read quite low and high
for each separate data point i used the maximum number as some had 3 curves run in succession etc
TQ RANGE 227-242wtq AVE: 234whp
HP RANGE 276-283whp AVE: 279whp
yours was 233/276 when reduced by ~2% to estimate SAE.
gotta hand it to dynojet they are pretty consistent when each of these dynos is a different physical machine scattered around a large continent.
where as locally on a dyno dynamics shootout ive seen 180rwkw vs 210rwkw you get a bif difference between different shopsLast edited by digger; 04-08-2015, 02:42 AM.89 E30 325is Lachs Silber - currently M20B31, M20B33 in the works, stroked to the hilt...
new build thread http://www.r3vlimited.com/board/showthread.php?t=317505
Comment
-
Another bone stock E46M3 272STD=~268SAE
Check Us out on Facebook
Needing a harness adapter or wiring help? Check it out: also have 24v motor mounts, E30 M3 covers and E36 ECU mounts!
Full Product Line Tuning
OBD2 Tuning Available! OBD2 E36, S54 Swap, S62 Swap, etc: tuning@MarkertMotorWorks.com Dyno Thread
Comment
-
Originally posted by DesertBMW View PostAdvertised was 333hp at the flywheel, this means there is a massive drop in horsepower trough the drivetrain (61 hp drop)
Non-rebuilt Spec e30's do about 150whp (~10% loss over advertised), but e30's less rotating mass with the brakes, hubs, less gears in the transmission, smaller differential gears etc etc.
Keep in mind catalyst, big mufflers, A/C, P/S etc also cause losses.
EDIT: Customer in line before me at the last dyno session had an e46m3 with Alpha-N and carbon air box made 280whp.
Comment
-
I was using that as somewhat of an example of this dyno reading ~3-4% low. :P
That is normal numbers (on our dyno) for a good E46M3 (stock)
Check Us out on Facebook
Needing a harness adapter or wiring help? Check it out: also have 24v motor mounts, E30 M3 covers and E36 ECU mounts!
Full Product Line Tuning
OBD2 Tuning Available! OBD2 E36, S54 Swap, S62 Swap, etc: tuning@MarkertMotorWorks.com Dyno Thread
Comment
-
Originally posted by DesertBMW View PostWith all the hype and the price of S54, I am not impressed at all.
Comment
-
Highest stockish one weve seen was a bottom up stock rebuild with headers on stock US tune did 295 (shown on first post), tuned to 317whp on stock airbox/cams. Most M50 manifold S52s dyno around 230-235 on our dyno, with nice ass headers and a more agressive tune ive done ~255whp on stock cams S52, so youre getting ~60whp for 4-5k+ not to mention the powerband increase.
Check Us out on Facebook
Needing a harness adapter or wiring help? Check it out: also have 24v motor mounts, E30 M3 covers and E36 ECU mounts!
Full Product Line Tuning
OBD2 Tuning Available! OBD2 E36, S54 Swap, S62 Swap, etc: tuning@MarkertMotorWorks.com Dyno Thread
Comment
-
best stock cam S52 vs best stock cam/airbox s54
Check Us out on Facebook
Needing a harness adapter or wiring help? Check it out: also have 24v motor mounts, E30 M3 covers and E36 ECU mounts!
Full Product Line Tuning
OBD2 Tuning Available! OBD2 E36, S54 Swap, S62 Swap, etc: tuning@MarkertMotorWorks.com Dyno Thread
Comment
-
sadly its all been downhill since the S5489 E30 325is Lachs Silber - currently M20B31, M20B33 in the works, stroked to the hilt...
new build thread http://www.r3vlimited.com/board/showthread.php?t=317505
Comment
Comment