M20 - R3VLimited Forums

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

	Topics		Statistics	Last Post
	Sticky: Stroking/boring M20B25/B27: Sectioned blocks show critical dimensions. PICS! by LJ851 Started by LJ851, 04-14-2013, 11:13 AM		98 responses 39,343 views 0 likes	Last Post by digger 08-28-2022, 04:24 PM
	Sticky: 1.3 Motronic Up-Grade & 2.7i How To by kenika65 Started by kenika65, 12-17-2007, 10:27 PM		499 responses 193,877 views 0 likes	Last Post by herschelcv 08-21-2022, 01:13 PM
	Fuel guage reads half full while empty by E30Gus Started by E30Gus, 07-15-2010, 02:53 PM		4 responses 509 views 0 likes	Last Post by E30Gus 07-15-2010, 03:13 PM
	Increasing compression - Milling? by Chuckcruzin1986 Started by Chuckcruzin1986, 06-27-2010, 10:40 AM		21 responses 1,296 views 0 likes	Last Post by nando 07-15-2010, 07:00 AM
	water pump, tensioner, & fan clutch by charliev68 Started by charliev68, 07-14-2010, 05:07 PM		2 responses 425 views 0 likes	Last Post by Sagaris 07-14-2010, 06:32 PM
	Loud engine + sputtering by pcaceres1982 Started by pcaceres1982, 07-13-2010, 10:14 PM		2 responses 449 views 0 likes	Last Post by pcaceres1982 07-14-2010, 03:09 PM
	327i build- what is the best diff? by phenryiv1 Started by phenryiv1, 07-13-2010, 08:26 AM		5 responses 638 views 0 likes	Last Post by DmcL 07-13-2010, 05:15 PM
	cold idle issues in the 85'e by Johnny Redline Started by Johnny Redline, 07-13-2010, 11:27 AM		2 responses 408 views 0 likes	Last Post by jlevie 07-13-2010, 02:21 PM
	What to check after over heating? by jayuuey Started by jayuuey, 07-13-2010, 09:08 AM		5 responses 431 views 0 likes	Last Post by jlevie 07-13-2010, 02:19 PM
	looked at an 89 iC today, 325E motor?! by 2.5-12 Started by 2.5-12, 07-01-2010, 08:33 PM		10 responses 1,358 views 0 likes	Last Post by 2.5-12 07-13-2010, 05:57 AM
	erratic idleing and sputtering by donkeynuts Started by donkeynuts, 06-30-2010, 05:04 PM		3 responses 664 views 0 likes	Last Post by bear 07-12-2010, 08:04 PM
	Head gasket replacement by DminLA Started by DminLA, 07-12-2010, 02:48 PM		4 responses 741 views 0 likes	Last Post by Farbin Kaiber 07-12-2010, 05:07 PM

Previous 1 326 726 776 816 823 824 825 826 827 828 829 836 876 926 1106 template Next

No topics found.

Mark This Channel Read

Working...

X