PNW Chit Chat thread

[Rennsport]

That moment you find out your injectors are much smaller than what you thought you had.

[Pdxseth]

Fuck my life, picking up a 24v Friday. Smh wish I could afford that m20 life.

[HarukoE30]

Id just rent the hoist, you can get a nice hoist for like $50-75 a day.

Hows the engine in that car?

I know a place, which would work, but the engine will be out for a mild while so travel time & all that adds up. I did do this method on the barn swap.

Not a whole lot of information on the engine, which once I get it on a stand I'll know more, but was told by the previous owner it ran great when running. The car developed a starter & ignition wire issue(s) which makes sense in post# 30080 from what the Previous~Previous owner had installed. Previous owner did however install a new timing belt / water pump etc. roughly a few hundred miles before parking it for the winter last year where it has sat for almost 10 months. I'll still change those parts as well

Kinda curious to learn more about the 88' engine, because 88' seems like the transitional period for E30 as a whole, but don't quote me on that.

You can borrow mine with the leveler for a six pack. Located in Bothell, WA.

I'll keep that in mind if my sister heads down from Everett soon.

harbor freight + 20% off coupon gogogogogogo. unless you are 100% sure you can get it done in 1-2 days, you're better off buying one and selling it when you're done.

Do they have decent folding one's? I haven't seen/check the R3v HB thead in awhile.

That moment you find out your injectors are much smaller than what you thought you had.

I'll try to remember this when looking for the right M50 injectors.

[delamaize]

Fuck my life, picking up a 24v Friday. Smh wish I could afford that m20 life.

Going to the dark side I see.....Hopefully will join you one of these days.

[Rennsport]

For when you do get injectors,

http://www.fuelinjector.citymaker.com/Fuel_Injector_Flow_Rates.html

Good table of the Bosch fuel injector specs.

Cheapest I've been able to find so far for brand new ones is on amazon.

[HarukoE30]

So pissed I need to buy a damn oxygen acetylene torch kit to get off this damn last drive shaft bolt.

[Pdxseth]

So pissed I need to buy a damn oxygen acetylene torch kit to get off this damn last drive shaft bolt.

I wish mine were on that good.

[BraveUlysses]

yes it folds:

http://www.harborfreight.com/1-ton-c...ane-69512.html

they have a 2ton one too.

[Gerta]

Little more then I wanted to spend for a Tire Pressure Gauge/Chuck but after using my coworkers Blue Point digi gauge I had to have one for the home garage.





Sent from my Nexus 4 using Tapatalk

That's bad ass. Do you get a shop discount on those? I'd love to start collecting some Matco stuff.

[kid325e]

Yeah I do. I'm not going to get EVERYTHING Snap-on/Matco/Mac but for the stuff I use all the time, it's nice to have something quality. Especially when I see the nice stuff the tech's at the shop have. The Blue Point one was tempting but just couldn't spend that much on a damn tire pressure gauge. lol

[Gerta]

That is a useful deal though. I would spend money on that or a quality digital torque wrench ... everyday tools the craftsman are good enough for my ham hands.

[Pdxseth]

Seriously! Where are all the 3.73 lsd's ???? I need one!

[iansane]

Who lives around me? Aside from Gerta? I'm off of 228th near the Kenmore gun range.

I'm directly across Bothell-Everett Hwy from you. I know I used to see MulletMan's e30 down the street from me a bit but I don't know if he sold it?

[Pdxseth]

Seriously! Where are all the 3.73 lsd's ???? I need one!

I'm too impatient, started looking 4 hours ago, already found one, I love the internets.

[Wschnitz]

I'm too impatient, started looking 4 hours ago, already found one, I love the internets.

Seth you said it was in Everett area you found it? wanna bring me some shit from portland?