M20 - R3VLimited Forums

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

	Topics		Statistics	Last Post
	Sticky: Stroking/boring M20B25/B27: Sectioned blocks show critical dimensions. PICS! by LJ851 Started by LJ851, 04-14-2013, 11:13 AM		98 responses 39,270 views 0 likes	Last Post by digger 08-28-2022, 04:24 PM
	Sticky: 1.3 Motronic Up-Grade & 2.7i How To by kenika65 Started by kenika65, 12-17-2007, 10:27 PM		499 responses 193,601 views 0 likes	Last Post by herschelcv 08-21-2022, 01:13 PM
	Billows of white smoke.... by terible1biker57 Started by terible1biker57, 07-17-2010, 08:33 PM		4 responses 573 views 0 likes	Last Post by jlevie 07-18-2010, 10:32 AM
	sounds like a diesel and smells like clutch :/ by kronus Started by kronus, 07-17-2010, 08:08 PM		1 response 442 views 0 likes	Last Post by jlevie 07-18-2010, 08:48 AM
	Intermediate bad miss at part throttle by yellowducman Started by yellowducman, 07-15-2010, 06:14 AM		6 responses 582 views 0 likes	Last Post by jlevie 07-17-2010, 07:38 AM
	driveshaft center support? by Est88 Started by Est88, 07-15-2010, 07:57 PM		5 responses 498 views 0 likes	Last Post by ForcedFirebird 07-17-2010, 06:53 AM
	spark plug wire symptoms? by jasonsnoddy Started by jasonsnoddy, 07-16-2010, 12:21 AM		5 responses 698 views 0 likes	Last Post by jlevie 07-16-2010, 02:16 PM
	noob question: swaping m20 into a 318 by Brezzi Started by Brezzi, 07-15-2010, 09:19 PM		3 responses 430 views 0 likes	Last Post by ZekeTheSneak 07-16-2010, 11:39 AM
	Fuel Pump Flow Rate by Scutt Started by Scutt, 07-08-2010, 07:58 PM		5 responses 1,143 views 0 likes	Last Post by jlevie 07-15-2010, 05:19 PM
	Alternator pulley upgrade? by blocke Started by blocke, 07-15-2010, 02:22 PM		1 response 727 views 0 likes	Last Post by jlevie 07-15-2010, 03:19 PM
	Fuel guage reads half full while empty by E30Gus Started by E30Gus, 07-15-2010, 02:53 PM		4 responses 505 views 0 likes	Last Post by E30Gus 07-15-2010, 03:13 PM
	Increasing compression - Milling? by Chuckcruzin1986 Started by Chuckcruzin1986, 06-27-2010, 10:40 AM		21 responses 1,290 views 0 likes	Last Post by nando 07-15-2010, 07:00 AM

Previous 1 325 725 775 815 822 823 824 825 826 827 828 835 875 925 1106 template Next

No topics found.

Mark This Channel Read

Working...

X