FORGED FULLY 🐬 grey S50,shaved, KW, brembos, garret g30/770 fr&rear 5 lug,

[Vtec?lol]

First of all, I used brand new bearings on the rods and mains , there's nothing wrong with re-using piston rings off a motor that ran and if its going on to the same cylinder that it began in , I have perfect compression , no rod knocks nothing was half ass on my build .
The only thing I should have done was buy a new oil pump.
New bearings
New guides
New stem seals
3 angle valve job
I have hundreds in just machine shop fees .
All new seals throughout the whole motor without a single leak , I didn't do anything incorrect on my build.
My oil squirter tube was clogged from debris in the oil so I burned a cam lobe and rocker , wooptee doo
I spent more money than you could possibly think is possible for this motor.
Reusing my rings may have been a risk but how come I have perfect compression , hmmmmmm well I have nothing to prove to you , but I take offense to people who have negitive opinions to say how about how I built my engine when I doubt you even attempted something as challenging and time consuming , as I have .
My rims are multi colored because its below 35 outside . I doubt goo off is going to take 3 layers of paint off my wheels .

Whoa there.

[efficient]

http://www.r3vlimited.com/board/showthread.php?t=256532&highlight=m20+valve+cover+running

[2mAn]

I've got all good compression in all the cylinders
#1 92
#2 90
#3 89
#4 91
#5 93 cylinder with rocker noise
#6 90

I have perfect compression

[e30m20TurbO7]

New shift knob


Smoked signals

[Farbin Kaiber]

Engine has half of correct compression.

Buys new shiftknob.



Memeworthy if I've ever seen it.

[e30m20TurbO7]

Here's my spectacular update , thanks to hoodlems who don't like my car Appernttly




Only people with nothing better to do , comment on what I do with my money , mind your own buisness , my project thread isn't a place to post your opinion .

Engine has half of correct compression.

Buys new shiftknob.



Memeworthy if I've ever seen it.

[Farbin Kaiber]

I've got tons better to do, I just choose to post my opinion in your project thread, if it wasn't the truth and you knew it, you wouldn't have been offended.

[e30m20TurbO7]

Did anyone ask for you opinion , Noo . Frankly it didn't offend me , they were gifts so I didn't even think twice about your "memeworthy" BS . I don't nessacarely drop it when people post rude things , with out expressing my opinion . You obviously don't have anything better to do because you replied to my post with in like 2 minutes . But whatever

Engine has half of correct compression.

Buys new shiftknob.



Memeworthy if I've ever seen it.

I've got tons better to do, I just choose to post my opinion in your project thread, if it wasn't the truth and you knew it, you wouldn't have been offended.

[Cronopoulos]

Oo lawd

[Justin B]

Sure you're not missing a 1 off each one of those numbers? Good lord.

[Cronopoulos]

is timing off a tooth?

[e30m20TurbO7]

My compression is fine I later found out it happend to be the gauge .
I put oil in my cylinder and ran a compression test . All my numbers when up to 120-125 psi

is timing off a tooth?

[e30m20TurbO7]

It's been pretty cold latley , getting down to the negitive's
But today I got adventourous , and decided to put on some stuff I had lieing around on



I spent a good two hours making it 100% straight with some wood , hammers and Dolly's
I need to start paint and body I spring

[efficient]

so you ever figure out what was wrong with your motor?

[FLG]

Oil in the cylinders bumping up compression points too bad rings

Sent from my Galaxy Nexus using Tapatalk 2