Oh hawt damn, how crusty is this jam?
Announcement
Collapse
No announcement yet.
My Hoopte30 Project Attempt #6 - the painless way to earn cash back every day
Collapse
X
-
Originally posted by 2mAn View PostShould've just bought the farm and got the cars for free
Originally posted by moatilliatta View PostOh hawt damn, how crusty is this jam?
Originally posted by Panici View PostWhat front valance is that? Alpina?
------
I thought y'all would appreciate a screen grab of where all the cars sat when I first rolled up to this place. I was only ever supposed to absorb the three E30s and the E28 down in the field, but they ended up needing to sell the farm, so the opportunity grew over the course of a few years. Pretty crazy this was just 20 minutes south of me
Untitled by Bobbie Morrone, on Flickr
- Likes 1
Comment
-
Texas holdem is still coming along! I swapped in a new updated genuine AUX fan, bypassed the low speed relay, and swapped over to r134 orings "while I was in there".
I also washed the car for the first time and paid way too much for a front toe adjustment so I could jump down to Louisville to see the legendary e30austin who was randomly in town.
We got pizza with moatilliatta and 02faq pal #dasfrogger. WE SHALL KEEP THE SPIRIT OF THE FORUM ALIVE
Kinda shocked texas holdem is where it is today. A mechanically restored car drives.... quite well. Got 24mpg too grippin' and rippin' on my way down with an s4.10
Sold my last good AC compressor, some coilovers and an s3.73 on my way down so it wasn't all a loss
Untitled by Bobbie Morrone, on Flickr
Untitled by Bobbie Morrone, on Flickr
Untitled by Bobbie Morrone, on Flickr
Untitled by Bobbie Morrone, on Flickr
- Likes 1
Comment
-
Originally posted by 2mAn View PostNo pic with the bros?!
Untitled by Bobbie Morrone, on Flickr
- Likes 3
Comment
-
Originally posted by e30austin View Post
HELL YEA, BROTHRRRRRRRRRRRRRRRRRRRRRRRRrrrrrrrrrrrrr
Originally posted by 2mAn View PostI wonder how many E30s have died in pieces in those hands that ate pizza together?
-------
I have unturned the A/C stone on Texas Holdem... I told myself I wasn't going to do it, but that '91 I just parted was retrofitted already and I had some good parts on the shelf so here we go lol.
I'm using the stock condenser with the updated BMW aux fan with the low speed resistor bypassed.
I installed the r134 drier, single pressure switch, and wired the low pressure switch closed, as the new single pressure switch provides both high and low pressure safeties. I jumped the updated pressure switch wiring and hit snowflake to make sure I had 12v at the clutch wire (compressor grounds to the engine) and all was well.
The compressor I pulled off of the '91 is the later seiki unit. The wiring was cut to the compressor but the system had fresh oil in it, so I am hoping for the best. Worst case scenario, I scored a rebuilt seiki off of rockauto a while back I have been saving for something like this that I can install if this one is no good. It spins freely, builds pressure spinning by hand, and clutch engages/disengages smoothly.
The seiki lines are different than the bosch lines on the car (compressor to cabin and compressor to condenser), so I have them ready to go.
Under the dash I installed the evaporator from the '91 as well as a new r134 expansion valve I had on the shelf.
I wrote a note to the next guy, lol, hoping no one sees it.
Green orings all the way around. I'm going to pull vacuum on the system tomorrow and hope for the best!
I also installed cruise back onto the car tonight now that it's no longer a parts car. The cluster I refreshed for the car had a main board issue, so I have a tested main board going in that cluster so I finally get blinkers on the dash.
Untitled by Bobbie Morrone, on Flickr
Untitled by Bobbie Morrone, on Flickr
Untitled by Bobbie Morrone, on Flickr
Untitled by Bobbie Morrone, on Flickr
Untitled by Bobbie Morrone, on Flickr
Cruise back in bizz
Untitled by Bobbie Morrone, on Flickr
Comment
-
Originally posted by raymang View PostYour evaporator core looks in better shape than mine did when I pulled it out lol. Maybe I should’ve cut that foam corner. Ah well it’s all buttoned up now 🫡
Comment
Comment