M20 - R3VLimited Forums

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

	Topics		Statistics	Last Post
	Sticky: ForcedFirebird's m20 dyno thread. by ForcedFirebird Started by ForcedFirebird, 04-17-2018, 01:07 AM		171 responses 22,497 views 0 reactions	Last Post by digger 07-28-2026, 06:09 PM
	Sticky: Stroking/boring M20B25/B27: Sectioned blocks show critical dimensions. PICS! by LJ851 Started by LJ851, 04-14-2013, 10:13 AM		98 responses 40,907 views 0 reactions	Last Post by digger 08-28-2022, 03:24 PM
	Sticky: 1.3 Motronic Up-Grade & 2.7i How To by kenika65 Started by kenika65, 12-17-2007, 09:27 PM		499 responses 198,619 views 0 reactions	Last Post by herschelcv 08-21-2022, 12:13 PM
	Miller maf with bbr chip? by actletpone Started by actletpone, 01-22-2014, 10:18 PM		6 responses 533 views 0 reactions	Last Post by actletpone 01-23-2014, 09:36 PM
	Any suggestion would help a lot. Rebuilt m20 help by Kevin_e30 Started by Kevin_e30, 12-21-2013, 12:02 PM		14 responses 774 views 0 reactions	Last Post by redlightpete 01-23-2014, 08:49 PM
	randomly missing?????? by custom e30 Started by custom e30, 01-21-2014, 07:18 PM		4 responses 405 views 0 reactions	Last Post by custom e30 01-23-2014, 10:40 AM
	91 318is swap m20 help! by reyesch3 Started by reyesch3, 01-21-2014, 11:56 AM		3 responses 622 views 0 reactions	Last Post by reyesch3 01-22-2014, 07:09 PM
	where do i find new intermediate shaft bearings? by doktor_b Started by doktor_b, 01-21-2014, 11:16 AM		8 responses 582 views 0 reactions	Last Post by richard.bratton 01-22-2014, 06:42 PM
	m20 valve noise / tick by 42000 Started by 42000, 01-20-2014, 01:58 PM		16 responses 1,333 views 0 reactions	Last Post by 42000 01-22-2014, 06:00 PM
	Question on CPS and tach feed wire routing. by Eecen Started by Eecen, 01-21-2014, 05:32 PM		4 responses 767 views 0 reactions	Last Post by Eecen 01-21-2014, 06:11 PM
	93 octane Mark D'Sylva chip can I run 91? by Hoffbrohaus Started by Hoffbrohaus, 01-20-2014, 10:23 AM		3 responses 768 views 0 reactions	Last Post by digger 01-21-2014, 02:50 PM
	Cylinder Wall Inspection After Hydrolock Conditions by Earendil Started by Earendil, 01-06-2014, 10:35 AM		4 responses 3,339 views 0 reactions	Last Post by Earendil 01-20-2014, 09:21 PM
	Is my new camshaft defective? by Earendil Started by Earendil, 01-10-2014, 12:41 PM		11 responses 1,065 views 0 reactions	Last Post by Earendil 01-20-2014, 05:18 PM

Previous 1 314 364 404 411 412 413 414 415 416 417 424 464 514 914 1115 template Next

No topics found.

Working...